Search results

'''Note:''' This should generally not be necessary for users, please just use the provided [[Mac_OS_X#Binary_Disk Install [http://brew.sh Homebrew] (not covered here, see Homebrew docs for details) and all sigrok build dependenc

...ogged data is supported by sigrok; configuring the device is not currently supported. [[Category:Supported]]

| status = supported '''Note:''' This device should not be confused with another (more recent) multimeter from PeakTech which is ''

* It's not a very precise specification. For example, there is no way to specify that ...e, and only allows for very simple triggers to be specified. Some hardware supported by sigrok is capable of much more complex triggering.

| status = supported ...nly the logic analyzer parts are currently implemented (analog sampling is not).

| status = supported ...le high speed USB link and (bursts of?) 60MHz using synchronous FIFO mode (not implemented in the sigrok driver).

See [[Supported hardware#GPIB_interfaces]] for the list of devices planned/supported in sigrok. | bgcolor="lime" align="center" | supported

| status = supported The DMM does not transmit samples after power up.

...k driver uses the chip, for example an FTDI chip, in a special mode (i.e., not as a plain COM port), the Zadig steps outlined below '''will''' be required The device specific USB driver shipped with the vendor software is '''not''' going to work in almost all cases. You will need to install the '''WinUS

Having quality, detailed pictures of supported devices is an important part of the sigrok project. It enables users to eas ...mugshots is that they will be placed on a transparent background in the [[Supported hardware]] page. It's surprising how small imperfections in an image become

...unication is required (the above mentioned ++ commands), which sigrok does not provide. ...n from the Arduino board to the Centronics connector, and driver chips are not involved. This keeps the component count low, the wiring simple, and the m

| status = supported | samplerate_state = State analysis not supported

bCountryCode 0 Not supported bCountryCode 0 Not supported

bCountryCode 0 Not supported bCountryCode 0 Not supported

bCountryCode 0 Not supported bCountryCode 0 Not supported

| status = supported ...he same USB VID:PID identification. It even appears as if these values are not specific to the logic analyzers: Linux' lsusb command "mistakes" these as a

** This is part of the standard [[OpenBSD]] install (not an extra package), apparently. ** libavahi-client-dev (dependency for librevisa, but not automatically installed on Debian)

| status = supported With 8 channels enabled, sample rates up to 40.8 MHz are supported.

| status = supported | amplitude = not specified in the data sheet (UI claims -10V .. +10V)

bCountryCode 0 Not supported

| status = supported ...onse to the '''*IDN?''' command, see below). If you have a device which is not yet [https://sigrok.org/gitweb/?p=libsigrok.git;a=blob;f=src/hardware/korad

| status = supported ...ioshack.com/product/index.jsp?productId=12988573 RadioShack 22-039]. It is not yet clear if the 22-039 is the same device as the 22-812.

| status = supported ...ss firmware versions. Password protection for TCP sockets is currently not supported.

-L, --list-supported Show information about supported hardware drivers, input file

bCountryCode 0 Not supported

bCountryCode 0 Not supported

| status = supported ...ange">UM34C</span> support detecting additional charging modes. This does not affect the line/load from negotiating a charging mode, just the meter's abi

It's just serial-over-USB, supported by the Linux kernel through the '''[http://git.kernel.org/?p=linux/kernel/g ...r writes are 4bits for addr, 8 bits for value, 2 unused bits and 2 bits im not sure what they are for :)

...so on. We do '''not''' list devices without PC connectivity, as those are not really useful for sigrok. ...kinds of devices here, not only [[Supported_hardware#Logic analyzers|those supported by sigrok]].

The following logic analyzer / mixed-signal devices are supported (if marked as such) by fx2lafw (and by the [http://sigrok.org/gitweb/?p=lib ¹ Analog signal support is not yet implemented.<br />

=== Supported samplerates === The following samplerates are supported in older firmware versions:

* Nightly AppImage binaries (oldest distro supported is Ubuntu 18.04): Note: Not provided as of Sept 2023 due to limited project manpower and low user inter

| status = supported * USB micro for host communication and measurement device supply (to not affect the DUT measurements in low load situations)

| status = supported ...e. This version has been tested to work, but more recent versions are not supported currently (see [https://sigrok.org/bugzilla/show_bug.cgi?id=989 bug #989]).

...rok.git;a=summary latest git version of libsigrok] (fewer devices might be supported in tarball releases) and devices we plan to support in the future. The [htt ...und-color: lime">supported</span>: [[:Category:Supported|{{PAGESINCATEGORY:Supported|pages}}]], [[File:Nuvola Orange.png|16px]] <span style="background-color: o