Difference between revisions of "Hantek 6022BE"
Uwe Hermann (talk | contribs) |
Uwe Hermann (talk | contribs) m (→Firmware) |
||
| Line 68: | Line 68: | ||
== Firmware == | == Firmware == | ||
In order to use this device, the [[fx2lafw|sigrok-firmware-fx2lafw]] (>= 0.1.4) firmware is required. | In order to use this device, the [[fx2lafw|sigrok-firmware-fx2lafw]] (>= 0.1.4) firmware is required. | ||
The firmware was originally written by Jochen Hoenicke (see [http://sigrok.org/gitweb/?p=sigrok-firmware-fx2lafw.git;a=blob;f=README README] for details), thanks a lot! | The firmware was originally written by Jochen Hoenicke (see [http://sigrok.org/gitweb/?p=sigrok-firmware-fx2lafw.git;a=blob;f=README README] for details), thanks a lot! | ||
Revision as of 00:36, 2 November 2016
The Hantek 6022BE is a USB-based, 2-channel oscilloscope with an analog bandwidth of 20MS/s and 48MS/s sampling rate.
See Hantek_6022BE/Info for more details (such as lsusb -v output) about the device.
Hardware
- USB: Cypress CY7C68013A-100AXC (FX2LP) (datasheet)
- 256-byte I²C EEPROM: Microchip 24LC02BI (datasheet)
- 16-Bit bus transceiver with 3-state outputs: TI SN74LVC16245A (datasheet)
- 1A low-dropout voltage regulator (3.3V): Advanced Monolithic Systems AMS1117-3.3 (datasheet)
- 2W, fixed input, isolated & unregulated dual/single output DC/DC converter: Mornsun A_S-2WR2 (A0505S-2WR2) (datasheet)
- ADC: ?
- Crystal: 24MHz
- Probes: ?
Photos
Box
Accessories
Probes
Device, top
Device, bottom
Device, connectors
Device, USB
PCB, top
PCB, bottom
Input stage
Cypress FX2LP
Microchip 24LC02BI
NXP 74HC4051D
AMS1117
Mornsun A0505S-2WR
Another teardown:
Device, top
PCB, top
PCB, bottom
Feedback resistor selector
Cypress FX2LP
Protocol
| Oscilloscope command | bRequest value | Notes |
|---|---|---|
| Set CH0 voltage range | 0xE0 | Possible values: 1,2,5,10 (5V, 2.5V, 1V, 500mV). |
| Set CH1 voltage range | 0xE1 | Possible values: 1,2,5,10 (5V, 2.5V, 1V, 500mV). |
| Set sampling rate | 0xE2 | Possible values: 48, 30, 24, 16, 8, 4, 1 (MHz) and 50,20,10 (*10kHz). |
| Trigger oscilloscope | 0xE3 | Possible values: 1 == start sampling. |
| Set number of channels | 0xE4 | Possible values: 1, 2. |
Firmware
In order to use this device, the sigrok-firmware-fx2lafw (>= 0.1.4) firmware is required.
The firmware was originally written by Jochen Hoenicke (see README for details), thanks a lot!
Note: The firmware is not flashed into the device permanently! You only need to make it available in the usual place where libsigrok looks for firmware files, it will be used automatically (and "uploaded" to the Cypress FX2's SRAM every time you attach the device to a USB port).