Search results
Jump to navigation
Jump to search
- '''Note:''' This should generally not be necessary for users, please just use the provided [[Mac_OS_X#Binary_Disk Install [http://brew.sh Homebrew] (not covered here, see Homebrew docs for details) and all sigrok build dependenc3 KB (499 words) - 15:13, 17 July 2023
- ...ogged data is supported by sigrok; configuring the device is not currently supported. [[Category:Supported]]1 KB (174 words) - 13:22, 17 December 2012
- | status = supported '''Note:''' This device should not be confused with another (more recent) multimeter from PeakTech which is ''1 KB (136 words) - 17:02, 15 December 2012
- * It's not a very precise specification. For example, there is no way to specify that ...e, and only allows for very simple triggers to be specified. Some hardware supported by sigrok is capable of much more complex triggering.3 KB (414 words) - 09:42, 9 August 2012
- | status = supported ...nly the logic analyzer parts are currently implemented (analog sampling is not).4 KB (595 words) - 21:01, 21 October 2022
- | status = supported ...le high speed USB link and (bursts of?) 60MHz using synchronous FIFO mode (not implemented in the sigrok driver).4 KB (576 words) - 19:22, 28 April 2022
- See [[Supported hardware#GPIB_interfaces]] for the list of devices planned/supported in sigrok. | bgcolor="lime" align="center" | supported3 KB (398 words) - 10:39, 12 October 2022
- | status = supported The DMM does not transmit samples after power up.3 KB (446 words) - 11:54, 8 March 2022
- ...k driver uses the chip, for example an FTDI chip, in a special mode (i.e., not as a plain COM port), the Zadig steps outlined below '''will''' be required The device specific USB driver shipped with the vendor software is '''not''' going to work in almost all cases. You will need to install the '''WinUS13 KB (2,022 words) - 10:40, 15 December 2023
- Having quality, detailed pictures of supported devices is an important part of the sigrok project. It enables users to eas ...mugshots is that they will be placed on a transparent background in the [[Supported hardware]] page. It's surprising how small imperfections in an image become4 KB (695 words) - 06:17, 13 November 2012
- ...unication is required (the above mentioned ++ commands), which sigrok does not provide. ...n from the Arduino board to the Centronics connector, and driver chips are not involved. This keeps the component count low, the wiring simple, and the m5 KB (830 words) - 09:13, 10 October 2023
- | status = supported | samplerate_state = State analysis not supported9 KB (1,338 words) - 15:30, 27 February 2022
- bCountryCode 0 Not supported bCountryCode 0 Not supported8 KB (626 words) - 22:47, 28 June 2012
- bCountryCode 0 Not supported bCountryCode 0 Not supported8 KB (627 words) - 15:44, 7 July 2012
- bCountryCode 0 Not supported bCountryCode 0 Not supported9 KB (706 words) - 03:33, 9 November 2012
- | status = supported ...he same USB VID:PID identification. It even appears as if these values are not specific to the logic analyzers: Linux' lsusb command "mistakes" these as a9 KB (1,321 words) - 09:18, 12 January 2023
- ** This is part of the standard [[OpenBSD]] install (not an extra package), apparently. ** libavahi-client-dev (dependency for librevisa, but not automatically installed on Debian)14 KB (2,040 words) - 12:40, 19 March 2023
- | status = supported With 8 channels enabled, sample rates up to 40.8 MHz are supported.10 KB (1,379 words) - 17:26, 1 December 2023
- | status = supported | amplitude = not specified in the data sheet (UI claims -10V .. +10V)5 KB (801 words) - 16:18, 7 October 2023
- bCountryCode 0 Not supported3 KB (209 words) - 00:41, 11 September 2012