sigrok - User contributions [en]

Metrix MX56C

2024-12-19T05:27:44Z

Tsaitgaist: replace user manual dead link

{{Infobox multimeter
| image = [[File:Metrix mx56c.png|180px]]
| name = Metrix MX56C
| status = supported
| source_code_dir = serial-dmm
| counts = 50000
| categories = CAT III (600V)
| connectivity = RS232
| measurements = voltage, resistance, diode, continuity, capacitance, frequency, duty cycle, pulse count, current, power, gain
| features = autorange, hold, relative, bargraph, backlight, true-rms, AC+DC
| website = [http://web.archive.org/web/20031103154311/http://www.chauvin-arnoux.com/produit/Famille_detail.asp?idFam=855&idPole=1 chauvin-arnoux.com]
}}

The '''Metrix MX56C''' is a 50000 counts, CAT III (600V) handheld digital multimeter with RS232 connectivity.

The same device was also sold as ''BK Precision 5390''.

== Hardware ==

The vendor specifically announces the high IP rating, and the advanced safety features.
The labelling suggests that "ASYC" stands for "Advanced Safety Concept".
Some models "lock" the probes, such that special action needs to be taken before they can get unplugged.
The battery and fuse compartment only can get accessed after the probes were removed.

The tilt stand at the back of the device can get removed, and then be used as a tool to open the front cover.
The locations for the tool during this activity are marked.
Removing the front cover allows access to the battery and the fuses.
The tool can be used to further open the device and remove the back cover as well, to access the PCB inside the meter.
But that activity is not suggested, and is not needed for regular use.

The location of the IR LEDs is rather unusual -- right underneath the range selector, within the battery compartment.
This is especially annoying as the meter has a high IP rating, which results in extra covers for improved isolation from environmental influences.
A special kit is sold for serial communication, which includes an alternative cover that replaces the originally shipped cover around the range selector.

(No further hardware details here, neither teardown images -- see the EEVblog link in the resources section.
Images there show a DMM chip labelled "ITT" and "METRIX DMM5", and a flyer for the serial communication kit.
User "free_electron" provides background on the ITT corporation.)

== Photos ==

<gallery>
File:mx56c-front-holster.png|front view, with holster
File:mx56c-back-instructions.png|back view, button and power-on instructions
File:mx56c-display-asyc-ip67.png|display, bargraph, ASYC(R) II label, IP67 rating
File:mx56c-batt-compart-ir-location.png|battery compartment, IR LED location
File:mx56c-batt-compart-covers.png|battery compartment, model name, rubber cover, tilt stand
</gallery>

== Protocol ==

=== Dumb mode (PRINT button) ===

When the user presses the PRINT button, the meter periodically sends measurement data via IR.
Holding the PRINT button allows adjustment of the interval (seconds resolution, up to 10 hours).
The PRINT button needs to get pressed again each time the function selection is changed.

Data is communicated via UART frames in 8n1 format at 2400bps.
All communicated bytes are in the ASCII range.
Each packet consists of 16 bytes which includes the CR terminator.
The packet contains a (signed) number value, then scale factor and unit for the measurement, and optional flags.
The absence of separators between the packet's fields makes case _sensitive_ parsing essential,
case insensitive operation would become ambiguous and would even break successful operation of the driver.

$ '''stty -F /dev/ttyUSB0 2400'''
$ '''hexdump -Cv < /dev/ttyUSB0'''
00000000 2d 30 2e 30 30 30 34 20 56 64 63 20 20 20 20 0d |-0.0004 Vdc .|
00000010 20 30 2e 30 30 30 37 20 56 64 63 20 20 20 20 0d | 0.0007 Vdc .|
00000020 20 30 2e 30 30 30 30 20 56 64 63 20 20 20 20 0d | 0.0000 Vdc .|
00000030 20 30 2e 30 30 30 30 20 56 64 63 20 20 20 20 0d | 0.0000 Vdc .|
00000040 20 30 2e 30 30 30 30 20 56 64 63 20 20 20 20 0d | 0.0000 Vdc .|
00000050 20 30 2e 30 30 30 33 20 56 64 63 20 20 20 20 0d | 0.0003 Vdc .|
00000060 20 34 39 2e 36 39 33 4d 6f 68 6d 20 20 20 20 0d | 49.693Mohm .|
00000070 20 34 39 2e 39 38 37 4d 6f 68 6d 20 20 20 20 0d | 49.987Mohm .|
00000080 20 34 39 2e 39 38 35 4d 6f 68 6d 20 20 20 20 0d | 49.985Mohm .|
00000090 20 20 30 30 2e 30 30 6e 46 20 20 20 20 20 20 0d | 00.00nF .|
000000a0 20 20 30 30 2e 30 30 6e 46 20 20 20 20 20 20 0d | 00.00nF .|
000000b0 20 20 30 30 2e 30 30 6e 46 20 20 20 20 20 20 0d | 00.00nF .|

The sigrok driver currently only implements support for this PRINT mode.

=== Smart mode ("RS 232 mode") ===

When the PK button is pressed at power-on, "RS 232 mode" gets enabled.
All operation still is controlled by the meter's range selector and buttons, but UART communication via IR becomes bidirectional.
The peer can query the current mode and state (and needs to reflect on that in its subsequent communication, the available documentation explicitly warns about sending commands that don't match the meter's capabilities or mode!).
The peer can request the previous or a next measurement, which might result in higher update rates compared to the PRINT mode.

Requests and responses in this mode are variable width (model dependent!), and "mostly ASCII" with occasional use of control characters.
While packets are of variable length, there are no record separators which would allow for synchronization to the data stream, or recognition of frame borders independently from (assumed) presence of a specific model.
Maybe a sequence of ESC and ENQ/ACK might help when synchronization was lost.
See the ASYC2 related PDF in the resources section for details.

The sigrok driver currently lacks support for this mode.

== Resources ==

* [http://web.archive.org/web/20060319202158/http://www.chauvin-arnoux.com/produit/famille_liste.asp?idRub=1529&idpole=1 Vendor software]
* http://www.eevblog.com/forum/testgear/metrix-mx56c-bk-precision-5390-multimeter-teardown/
* [https://web.archive.org/web/20160313124153/http://www.chauvin-arnoux.us/pdfs_aemc/user-manuals/MX56_EN.pdf User Manual]
* http://www.snesometel.com.tn/images/PDF/NF-SX-ASYC2.pdf Interface description with protocol.

[[Category:Device]]
[[Category:Multimeter]]
[[Category:Supported]]

Voltcraft VC-870

2024-12-17T12:17:53Z

Tsaitgaist: replace dead links with wbm

{{Infobox multimeter
| image = [[File:Voltcraft vc870 mugshot.png|180px]]
| name = Voltcraft VC-870
| status = supported
| source_code_dir = serial-dmm
| counts = 40000
| categories = CAT III (1000V) / CAT IV (600V)
| connectivity = [[Device_cables#UNI-T_UT-D02|RS232]] / [[Device_cables#UNI-T_UT-D04|USB]]
| measurements = voltage, resistance, diode, continuity, capacitance, frequency, current, temperature, loop current, power + apparent power, power factor + frequency, effective voltage + current
| features = autorange, hold, relative, backlight, min, max, minmax, true-rms, bargraph
| website = [http://www.conrad.de/ce/de/product/124603/Hand-Multimeter-digital-VOLTCRAFT-VC870-CAT-III-1000-V-CAT-IV-600-V-Anzeige-Counts-40000 conrad.de]
}}

The '''Voltcraft VC-870''' is a 40000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity.

== Hardware ==

'''Multimeter''':

We don't have teardown photos yet, but [http://www.all-electronics.de/texte/anzeigen/43807/Digitalmultimeter-VC870 this article] (see also [http://www.all-electronics.de/upl/text/43/43807/media/23736.jpg this photo]) claims that the DMM contains the following components:
* '''4 3/4 and 5 3/4 digits ADC''': [http://www.cyrustek.com.tw/product-1-44000.htm#ES51966 Cyrustek ES51966] ([http://www.cyrustek.com.tw/spec/ES51966A.pdf datasheet])
* '''Microcontroller''': Texas Instruments MSP430
* '''Voltage regulators''': TPS76301, 7201u55
* '''EEPROM''': Atmel "748"
* '''True RMS-to-DC converter''': [http://www.analog.com/en/special-linear-functions/rms-to-dc-converters/ad737/products/product.html Analog Devices AD737] ([http://www.analog.com/static/imported-files/data_sheets/AD737.pdf datasheet])

'''RS232 cable:'''
* See [[Device cables#UNI-T_UT-D02]].

'''USB cable:'''
* See [[Device cables#UNI-T_UT-D04]].

== Photos ==

'''Multimeter''':

<gallery>
</gallery>

'''RS232 cable:'''

See [[Device cables#UNI-T_UT-D02]].

'''USB cable:'''

See [[Device cables#UNI-T_UT-D04]].

== Protocol ==

Some (partially incorrect and also incomplete) [https://web.archive.org/web/20190412085703/http://www.produktinfo.conrad.com/datenblaetter/100000-124999/124603-in-01-en-Interfaceprotokoll_VC_870_DMM.pdf protocol docs] are available from the vendor.

The interface parameters for the [[Device cables#UNI-T_UT-D02|UNI-T UT-D02]] serial cable are '''9600/8n1'''.

A packet consists of 23 bytes:

{| border="0" style="font-size: smaller" class="alternategrey sigroktable"
|-
!Byte(s)
!Name
!Description

|-
| 0
| '''Function code'''
| Bytes 0 and 1 determine the measurement mode.

|-
| 1
| '''Function select code'''
| Bytes 0 and 1 determine the measurement mode.

|-
| 2
| '''Range'''
|

|-
| 3-7
| '''5 main display digits'''
|

|-
| 8-12
| '''5 auxiliary display digits'''
|

|-
| 13
| '''?'''
|

|-
| 14
| '''?'''
|

|-
| 15
| '''Status'''
|

|-
| 16
| '''Option 1'''
|

|-
| 17
| '''Option 2'''
|

|-
| 18
| '''Option 3'''
|

|-
| 19
| '''Option 4'''
|

|-
| 20
| '''Dual display'''
|

|-
| 21
| '''Line feed'''
| Always 10 / 0x0a.

|-
| 22
| '''Carriage return'''
| Always 13 / 0x0d.

|}

Measurement modes:

{| border="0" style="font-size: smaller" class="alternategrey sigroktable"
|-
!Function code
!Function select code
!Measurement mode

|-
| 0x30
| 0x30
| DCV
|-
| 0x30
| 0x31
| ACV
|-
| 0x31
| 0x30
| DCmV
|-
| 0x31
| 0x31
| Temperature (Celsius and Fahrenheit)
|-
| 0x32
| 0x30
| Resistance
|-
| 0x32
| 0x31
| Continuity
|-
| 0x33
| 0x30
| Capacitance
|-
| 0x34
| 0x30
| Diode
|-
| 0x35
| 0x30
| Frequency
|-
| 0x35
| 0x31
| Loop current, (4-20mA)%
|-
| 0x36
| 0x30
| DCuA
|-
| 0x36
| 0x31
| ACuA

|-
| 0x37
| 0x30
| DCmA
|-
| 0x37
| 0x31
| ACmA
|-
| 0x38
| 0x30
| DCA
|-
| 0x38
| 0x31
| ACA
|-
| 0x39
| 0x30
| Active/real power + apparent power
|-
| 0x39
| 0x31
| Power factor + frequency
|-
| 0x39
| 0x32
| Voltage effective value + current effective value
|}

Notes:
* The bargraph value (only shown on the LCD for voltage, current, and resistance mode) is '''not''' contained in the protocol.
* The auto-poweroff feature which powers the device off after 15 minutes is always disabled when the PC interface is "active" (i.e. the user pressed the REL/PC button for 1 second). Thus the respective "auto-poweroff" bit/flag, which '''is''' contained in the protocol, always has the same value.
* The backlight status (on/off) '''is''' contained in the protocol.

== Resources ==

* [https://web.archive.org/web/20190412085707/http://www.produktinfo.conrad.com/datenblaetter/100000-124999/124603-an-01-ml-VOLTCRAFT_VC_870_DMM_de_en_fr_nl.pdf Manual]
* [https://web.archive.org/web/20190412085653/http://www.produktinfo.conrad.com/datenblaetter/100000-124999/124603-up-01-ml-VC_870_Ver_4_2_6_von_XP_bis_WIN7.zip Vendor software]
* [http://www.all-electronics.de/texte/anzeigen/43807/Digitalmultimeter-VC870 all-electronics.de: Voltcraft VC-870 review with photos] (German)

[[Category:Device]]
[[Category:Multimeter]]
[[Category:Supported]]

ZKETECH EBD-USB

2019-08-18T13:19:13Z

Tsaitgaist: /* Protocol */ add message

{{Infobox power supply
| image = [[File:Ztetech-ebd-usb+.png|180px]]
| name = ZKETECH EBD-USB+
| status = supported
| source_code_dir = zketech-ebd-usb
| channels = 1
| channel1 = 35W / 0-4A / 0-21V
| connectivity = USB/serial
| features = DC constant current load
| website = [http://www.zketech.com zketech.com]
}}

The '''ZKETECH EBD-USB+''' is a programmable DC electronic load (0~4A, 0~21V) with serial connectivity over USB.

The electronic load can only be used together with a computer, because it has no external controls.

Currently only the "plus" version is supported. Contact us for support if you own a "non-plus" version (25W / 13.5V).

See [[ZKETECH EBD-USB/Info]] for more details (such as '''lsusb -v''' output) about the device.

== Hardware ==

* '''Power MOSFET''': [https://www.infineon.com/cms/de/product/power/mosfet/20v-300v-n-channel-power-mosfet/40v-75v-n-channel-power-mosfet/irlz44n/ Infineon IRLZ44N] ([https://www.infineon.com/dgdl/irlz44npbf.pdf?fileId=5546d462533600a40153567217c32725 datasheet])

== Protocol ==

Messages are exchanged between host and devices:
* they start with 0xfa
* they end with 0xf8
* these two bytes values can't be used in the rest of the message (the maximum value is 240)
* the second byte encodes the message type
* all two-byte values are in base 240 (e.g. 01 0a = 250)
* the second last byte is a XOR checksum of the message (excluding first and last byte).

The communication is prone to byte loss on both directions.
Always verify the message length, checksum, and don't send the bytes too fast.
Resend messages until the one expected next is received.
Sometimes it doesn't send any messages anymore and doesn't react to sent messages.
Then the only way to reset the device is to re-plug it.

Messages:

* <code>fa 05 00 00 00 00 00 00 05 f8</code>
** direction: host to device
** description: start measurements
* <code>fa 06 00 00 00 00 00 00 06 f8</code>
** direction: host to device
** description: stop measurements
* <code>fa 01 00 64 00 0a 00 00 6f f8</code>
** direction: host to device
** description: start load
** content:
*** <code>00 64</code>: current limit in 0.001 A
*** <code>00 0a</code>: cutoff voltage in 0.01 V
*** <code>00 00</code>: time limit in minutes
** note: the time limit is not enforced on the device. the device will report the minutes passed, and the host needs to stop the load
* <code>fa 02 00 00 00 00 00 00 02 f8</code>
** direction: host to device
** description: toggle load on/off
* <code>fa 07 00 64 00 0a 00 00 69 f8</code>
** direction: host to device
** description: update load
** content:
*** <code>00 64</code>: current limit in 0.001 A
*** <code>00 0a</code>: cutoff voltage in 0.01 V
*** <code>00 00</code>: time limit in minutes
** note: the time limit is not enforced on the device. the device will report the minutes passed, and the host needs to stop the load
* <code>fa 04 00 14 c8 00 00 00 d8 f8</code>
** direction: host to device
** description: calibrate
** content:
*** <code>00</code>: 0x00 = low voltage, 0x01 = high voltage, 0x02 = low current, 0x03 = high current
*** <code>14 c8</code>: voltage in 0.001 V or current in 0.0001 A
* <code>fa 00 00 00 14 c5 07 a9 07 ad 00 64 00 0a 00 00 1a a1 f8</code>
** direction: device to host
** description: measurement, without load
** content:
*** <code>00 00</code>: current in 0.0001 A
*** <code>14 c5</code>: voltage in 0.001 V
*** <code>07 a9</code>: voltage of D+ 0.001 V
*** <code>07 ad</code>: voltage of D- 0.001 V
*** <code>00 64</code>: current limit in 0.001 A
*** <code>00 0a</code>: cutoff voltage in 0.01 V
*** <code>00 00</code>: time limit in minutes
*** <code>1a</code>: device (0x1a = EBD-USB+)
* <code>fa 0a 00 00 14 c5 07 a9 07 ad 00 64 00 0a 00 00 1a ab f8</code>
** direction: device to host
** description: measurement, with load
** content: same as measurement, without load
* <code>fa 0a 00 0a 00 00 00 00 00 f8</code>
** direction: device to host
** description: load timer
** content:
*** <code>00 0a</code>: time minutes passed since load start
* <code>fa 64 00 00 00 00 01 3b 00 e7 01 50 09 6f 10 a0 1a 24 f8</code>
** direction: device to host
** description: device measurement, without load
** content:
*** <code>00 00</code>: current in 0.0001 A
*** <code>00 00</code>: voltage in 0.001 V
*** <code>01 3b</code>: voltage of D+ 0.001 V
*** <code>00 e7</code>: voltage of D- 0.001 V
*** <code>01 50</code>: version in 0.01
*** <code>09 6f</code>: unknown (seems constant)
*** <code>10 a0</code>: unknown (seems constant)
*** <code>1a</code>: device (0x1a = EBD-USB+)
* <code>fa 6e 08 52 14 67 07 95 07 9c 01 50 09 6f 10 a0 1a d3 f8</code>
** direction: device to host
** description: device measurement, with load
** content: same as device measurement, without load

== Photos ==

<gallery>
File:Ztetech-ebd-usb+.png|Device, front
File:Zketech-ebd-usb+_top.jpg|Device, top
File:Zketech-ebd-usb+_bottom.jpg|Device, bottom
File:Zketech-ebd-usb+_left.jpg|Device, left
</gallery>

== Resources ==

* [http://www.zketech.com/nd.jsp?id=15#_np=101_304 Vendor software]

[[Category:Device]]
[[Category:Digital load]]
[[Category:Supported]]

ZKETECH EBD-USB

2019-08-18T08:54:30Z

Tsaitgaist: /* Protocol */ document protocol

{{Infobox power supply
| image = [[File:Ztetech-ebd-usb+.png|180px]]
| name = ZKETECH EBD-USB+
| status = supported
| source_code_dir = zketech-ebd-usb
| channels = 1
| channel1 = 35W / 0-4A / 0-21V
| connectivity = USB/serial
| features = DC constant current load
| website = [http://www.zketech.com zketech.com]
}}

The '''ZKETECH EBD-USB+''' is a programmable DC electronic load (0~4A, 0~21V) with serial connectivity over USB.

The electronic load can only be used together with a computer, because it has no external controls.

Currently only the "plus" version is supported. Contact us for support if you own a "non-plus" version (25W / 13.5V).

See [[ZKETECH EBD-USB/Info]] for more details (such as '''lsusb -v''' output) about the device.

== Hardware ==

* '''Power MOSFET''': [https://www.infineon.com/cms/de/product/power/mosfet/20v-300v-n-channel-power-mosfet/40v-75v-n-channel-power-mosfet/irlz44n/ Infineon IRLZ44N] ([https://www.infineon.com/dgdl/irlz44npbf.pdf?fileId=5546d462533600a40153567217c32725 datasheet])

== Protocol ==

Messages are exchanged between host and devices:
* they start with 0xfa
* they end with 0xf8
* these two bytes values can't be used in the rest of the message (the maximum value is 240)
* the second byte encodes the message type
* all two-byte values are in base 240 (e.g. 01 0a = 250)
* the second last byte is a XOR checksum of the message (excluding first and last byte).

The communication is prone to byte loss on both directions.
Always verify the message length, checksum, and don't send the bytes too fast.
Resend messages until the one expected next is received.

Messages:

* <code>fa 05 00 00 00 00 00 00 05 f8</code>
** direction: host to device
** description: start measurements
* <code>fa 06 00 00 00 00 00 00 06 f8</code>
** direction: host to device
** description: stop measurements
* <code>fa 01 00 64 00 0a 00 00 6f f8</code>
** direction: host to device
** description: start load
** content:
*** <code>00 64</code>: current limit in 0.001 A
*** <code>00 0a</code>: cutoff voltage in 0.01 V
*** <code>00 00</code>: time limit in minutes
** note: the time limit is not enforced on the device. the device will report the minutes passed, and the host needs to stop the load
* <code>fa 02 00 00 00 00 00 00 02 f8</code>
** direction: host to device
** description: toggle load on/off
* <code>fa 07 00 64 00 0a 00 00 69 f8</code>
** direction: host to device
** description: update load
** content:
*** <code>00 64</code>: current limit in 0.001 A
*** <code>00 0a</code>: cutoff voltage in 0.01 V
*** <code>00 00</code>: time limit in minutes
** note: the time limit is not enforced on the device. the device will report the minutes passed, and the host needs to stop the load
* <code>fa 04 00 14 c8 00 00 00 d8 f8</code>
** direction: host to device
** description: calibrate
** content:
*** <code>00</code>: 0x00 = low voltage, 0x01 = high voltage, 0x02 = low current, 0x03 = high current
*** <code>14 c8</code>: voltage in 0.001 V or current in 0.0001 A
* <code>fa 00 00 00 14 c5 07 a9 07 ad 00 64 00 0a 00 00 1a a1 f8</code>
** direction: device to host
** description: measurement (without load)
** content:
*** <code>00 00</code>: current in 0.0001 A
*** <code>14 c5</code>: voltage in 0.001 V
*** <code>07 a9</code>: voltage of D+ 0.001 V
*** <code>07 ad</code>: voltage of D- 0.001 V
*** <code>00 64</code>: current limit in 0.001 A
*** <code>00 0a</code>: cutoff voltage in 0.01 V
*** <code>00 00</code>: time limit in minutes
*** <code>1a</code>: device (0x1a = EBD-USB+)
* <code>fa 0a 00 00 14 c5 07 a9 07 ad 00 64 00 0a 00 00 1a ab f8</code>
** direction: device to host
** description: load measurement
** content:
*** <code>00 00</code>: current in 0.0001 A
*** <code>14 c5</code>: voltage in 0.001 V
*** <code>07 a9</code>: voltage of D+ 0.001 V
*** <code>07 ad</code>: voltage of D- 0.001 V
*** <code>00 64</code>: current limit in 0.001 A
*** <code>00 0a</code>: cutoff voltage in 0.01 V
*** <code>00 00</code>: time limit in minutes
*** <code>1a</code>: device (0x1a = EBD-USB+)
* <code>fa 0a 00 0a 00 00 00 00 00 f8</code>
** direction: device to host
** description: load timer
** content:
*** <code>00 0a</code>: time minutes passed since load start
* <code>fa 64 00 00 00 00 01 3b 00 e7 01 50 09 6f 10 a0 1a 24 f8</code>
** direction: device to host
** description: device measurement
** content:
*** <code>00 00</code>: current in 0.0001 A
*** <code>00 00</code>: voltage in 0.001 V
*** <code>01 3b</code>: voltage of D+ 0.001 V
*** <code>00 e7</code>: voltage of D- 0.001 V
*** <code>01 50</code>: version in 0.01
*** <code>09 6f</code>: unknown (seems constant)
*** <code>10 a0</code>: unknown (seems constant)
*** <code>1a</code>: device (0x1a = EBD-USB+)

== Photos ==

<gallery>
File:Ztetech-ebd-usb+.png|Device, front
File:Zketech-ebd-usb+_top.jpg|Device, top
File:Zketech-ebd-usb+_bottom.jpg|Device, bottom
File:Zketech-ebd-usb+_left.jpg|Device, left
</gallery>

== Resources ==

* [http://www.zketech.com/nd.jsp?id=15#_np=101_304 Vendor software]

[[Category:Device]]
[[Category:Digital load]]
[[Category:Supported]]

Device cables

2015-05-21T12:29:18Z

Tsaitgaist: /* UNI-T UT-D02 */ update link to product

This page contains information and teardown photos of various multimeter/datalogger/etc. PC connectivity cables and adapters.

= Multimeters =

== Agilent U1173A ==

The [http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&ckey=792204&nid=-536906710.536910943.00&id=792204&pselect=SR.GENERAL Agilent U1173A] is an IR-USB cable.

'''Hardware''':
* Prolific PL2303HX (max. baudrate 19200, according to the Agilent website)

''' Works with''':
* Agilent U1230/40/50/70 series
* Note: For the U1240 series, the additional [http://www.home.agilent.com/agilent/redirector.jspx?action=ref&lc=ger&cc=DE&nfr=-536906710.536910943&ckey=2101709&cname=PRODUCT U1179A] IR bracket is required.[http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&nid=-536906710.536910943&pageMode=OV 1]

''' Where to buy''':
* [http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&ckey=792204&nid=-536906710.536910943.00&id=792204&pselect=SR.GENERAL Agilent] ($31)
* [http://www.newark.com/agilent-technologies/u1173a/ir-to-usb-connectivity-cable-assembly/dp/04M7391 Newark] ($31)
* [http://www.datatec.de/U1173A-Agilent-Adapterkabel.htm Datatec] (€23)

<gallery>
File:Agilent U1173A.jpg|Device, front
File:Agilent U1173A PCB.jpg|PCB, front
File:Agilent U1173A PCB back.jpg|PCB, back
</gallery>

== Agilent U1177A ==

The [http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&ckey=2090364&nid=-536902461.1006710.00&id=2090364&pselect=SR.GENERAL Agilent U1177A] is an IR-Bluetooth interface module.

Notes: 9600 baud, 8n1 settings on the PC. The protocol (AT commands, documented in the [http://cp.literature.agilent.com/litweb/pdf/U1177-90002.pdf Agilent U1177A configuration guide]) allows changing the baud rate to 19200, among other things.[http://www.home.agilent.com/agilent/redirector.jspx?action=ref&cname=AGILENT_EDITORIAL&ckey=2150265&lc=ger&cc=DE&nfr=-536902461.1006710.00 1] Default Bluetooth PIN: 1234. For the U1240 series, the additional [http://www.home.agilent.com/agilent/redirector.jspx?action=ref&lc=ger&cc=DE&nfr=-536906710.536910943&ckey=2101709&cname=PRODUCT U1179A] IR bracket is required.[http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&nid=-536906710.536910943&pageMode=OV 2]

'''Hardware''':
* CSR BC417...
* Macronix MX...
* PCB markings: U1177-26500, REV004, MSD-02

''' Works with''':
* Agilent U1230/40/50/70 series

''' Where to buy''': 
It is often given away free as a promotion with one of the Agilent U12xxA meters, but can also be purchased separately:
* [http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&ckey=2090364&nid=-536902461.1006710.00&id=2090364&pselect=SR.GENERAL Agilent] ($49)
* [http://www.datatec.de/Agilent-1177A-Bluetooth.htm Datatec] (€36)

<gallery>
File:Agilent U1177A.jpg|Device, front
File:Agilent U1177A back.jpg|Device, back
File:Agilent U1177A battery.jpg|Battery compartment
File:Agilent U1177A PCB.jpg|PCB, front
File:Agilent U1177A PCB back.jpg|PCB, back
</gallery>

== Amprobe 38SW-A ==

The [http://www.amprobe.eu/en_GB/showproduct/234/38SW-A/ Amprobe 38SW-A] is an RS232 PC interface cable for the [http://www.amprobe.eu/en_GB/showproduct/134/38XR-A/ Amprobe 38XR-A] multimeter. The "38SW-A" name is also used to refer to the respective PC software for use with the serial cable.

'''Hardware''':
* TODO.

''' Works with''':
* [http://www.amprobe.eu/en_GB/showproduct/134/38XR-A/ Amprobe 38XR-A]

''' Where to buy''':
* [http://www.digikey.com/product-detail/en/38SW-A/38SW-A-ND/1540519 Digikey], [http://www.tme.eu/de/details/38sw-a/messgerate-software/amprobe/38sw/ TME.eu], [http://de.rs-online.com/mobile/p/digital-multimeter/0411722/ RS Components], [http://www.mercateo.com/p/115-911905/38SW_A_Interfacekabel_und_Software.html Mercateo], [http://www.testersandtools.com/Amprobe-38SW-A-RS232-Software-Cable.php testersandtools.com], [http://www.newark.com/amprobe-instruments/38sw-a/rs-232-cable-software-38xr-a/dp/29M6230 Newark], [https://www.distrelec.de/interfacekabel-und-software/amprobe/38sw-a/911905/de Distrelec], and various others.
* The usual price is around €20-€35, depending on vendor and location.

<gallery>
File:Amprobe 38sw a cable package top.jpg|Package, top
File:Amprobe 38sw a cable package bottom.jpg|Package, bottom
File:Amprobe 38sw a cable top.jpg|Cable, top
File:Amprobe 38sw a cable bottom.jpg|Cable, bottom
File:Amprobe 38sw a cable cdrom top.jpg|CD-ROM, top
File:Amprobe 38sw a cable cdrom bottom.jpg|CD-ROM, bottom
File:Amprobe 38sw a cable cdrom contents.jpg|CD-ROM, contents
File:Amprobe 38sw a cable open.jpg|Cable, opened
File:Amprobe 38sw a cable housing1.jpg|Housing 1
File:Amprobe 38sw a cable housing2.jpg|Housing 2
File:Amprobe 38sw a cable pcb top.jpg|PCB, top
File:Amprobe 38sw a cable pcb bottom.jpg|PCB, bottom
File:Amprobe 38sw a cable pcb pinout.jpg|PCB, pinout
</gallery>

== APPA / ISO-TECH IC50 ==

The IC50 is a USB PC interface cable for some APPA and ISO-TECH multimeters and thermometers.

''' Works with''':
* [http://www.appatech.com/appa_product_home.php?pdid=2005102401295373290&kindid=2005081003113623241 APPA 70] series multimeters (and ISO-TECH IDM 70 series clone)
* [http://www.appatech.com/appa_product_home.php?pdid=20051220112048498347&kindid=20050810031145946832 APPA 50] series thermometer (and RS 50 series clone)

''' Where to buy''':
* [http://uk.rs-online.com/web/p/multimeter-accessories/7048135/ RS 704-8135]
* The price is around 40 €

== APPA / ISO-TECH IC70 ==

The IC70 is an RS232 PC interface cable for some APPA and ISO-TECH multimeters and thermometers.

''' Works with''':
* [http://www.appatech.com/appa_product_home.php?pdid=2005102401295373290&kindid=2005081003113623241 APPA 70] series multimeters (and ISO-TECH IDM 70 series clone)
* [http://www.appatech.com/appa_product_home.php?pdid=20051220112048498347&kindid=20050810031145946832 APPA 50] series thermometer (and RS 50 series clone)

''' Where to buy''':
* [http://uk.rs-online.com/web/p/digital-multimeters/4609881/ RS 460-9881]
* The price is around 20 €

<gallery>
File:Ic70 optical serial cable.jpeg|Cable
</gallery>

== Brymen BC-85X(-1) ==

Not compatible with BC-85Xa.

TODO.

'''Hardware''':
* TODO.

''' Works with''':
* Brymen BM857/BM859 (non-a versions)

''' Where to buy''':
* Available from Greenlee as DMSC-9 (not DMSC-9U).
* [http://www.tme.eu/en/details/kitrs232c/meters-software/ TME] (€26.82)

=== Brymen BR85X interface kit ===

<gallery>
File:Brymen_br85x_cable.jpg|Kit contents (software disc not shown)
File:Brymen_br85x_rs232_conn.jpg|BC-85X-1 DB9 connector
File:Brymen_br85x_dmm_end.jpg|BC-85Xa DMM connector
</gallery>

== Brymen BRUA-20X ==

'''Hardware''':
* TODO.

''' Works with''':
* Brymen BM20x and BM25x series

''' Where to buy''':
* [http://www.tme.eu/en/details/kitbrua-20x/meters-software/brymen/ TME] (€30)

<gallery>
File:Brymen brua-20x package1.jpg|Package, top
File:Brymen brua-20x package2.jpg|Package, side
File:Brymen brua-20x package contents.jpg|Package contents
File:Brymen brua-20x bua-2303 front.jpg|BUA-2303, front
File:Brymen brua-20x bua-2303 bottom.jpg|BUA-2303, bottom
File:Brymen brua-20x bc-20x cable.jpg|BC-20X, cable
File:Brymen brua-20x bc-20x attached.jpg|BC-20X, attached
</gallery>

== Brymen BC-85Xa ==

Not compatible with BC-85X.

TODO.

'''Hardware''':
* TODO.

''' Works with''':
* Brymen BM857a/BM859a
* Extech MM570A/MM560A/MP530A/MP510A

''' Where to buy''':
* Available from Extech in a kit with USB-to-serial converter and software disc, under the name SW-810a.
* [http://de.mouser.com/Search/ProductDetail.aspx?qs=zS8Kl81wrHovBIt5EskF9A== Mouser] (€65.99)
* [http://www.tme.eu/de/details/sw810a/umgebungsmesser-sonstige/extech/ TME] (€60.60)

=== Extech SW-810a kit ===

This is a kit sold by Extech, containing the BC-85Xa RS232 cable, the BUA2303 USB-to-serial adapter, a USB cable, and a software disc.

<gallery>
File:Extech_sw810a_kit.jpg|Kit contents (software disc not shown)
File:Extech_sw810a_ir_db9.jpg|BC-85Xa DB9 connector
File:Extech_sw810a_id_dmm_hookup.jpg|BC-85Xa DMM connector
File:Extech_sw810a_usb2serial.jpg|BUA2303 USB-to-serial converter
File:Extech_sw810a_usb2serial_back.jpg|BUA2303 USB-to-serial converter, back
File:Extech_sw810a_usb2serial_bottom.jpg|BUA2303 USB-to-serial converter, bottom
File:Extech_sw810a_IR_opened.jpg|IR side, opened
File:Extech_sw810a_ir_casing.jpg|IR side casing
File:Extech_sw810a_ir_pcb_top.jpg|IR side PCB, top
File:Extech_sw810a_ir_pcb_bottom.jpg|IR side PCB, botoom
File:Extech_sw810a_usb2serial_pcb_top.jpg|BUA2303 PCB, top
File:Extech_sw810a_usb2serial_pcb_bottom.jpg|BUA2303 PCB, bottom
</gallery>

== Brymen BU-86X ==

See [[Brymen BU-86X/Info]] for more details (such as lsusb -v output).

'''Hardware''':
* Cypress CY7C63743 enCoRe USB

''' Works with''':
* Brymen BM867/BM869

''' Where to buy''':
* [http://www.tme.eu/en/details/kitbu-86x/instruments-de-mesure-logiciels/brymen/ TME] (40 €)

=== Brymen BU-86X interface kit ===

<gallery>
File:Bc86x_01_general.jpeg|Kit content (software disc not shown)
File:Bc86x_02_usb.jpeg|BC-86X USB connector
File:Bc86x_03_infrared.jpeg|BC-86X DMM connector
</gallery>

== Digitek DT4000ZC cable ==

The [[Digitek DT4000ZC]] (and the rebadged [[TekPower TP4000ZC]]) ship with this RS232 to 3.5mm stereo plug cable. The ring on the plug is left unconnected.

The cable works on the assumption that TX (pin 3) and DTR (pin 4) are at a fixed voltage and will not be toggled. TX should be below -3 V, and the resistor acts as a pull-down. DTR should be abouve 3V. The photodiode/phototransistor in the DMM will pull the RX pin above 3V when the IR diode is on.

'''Hardware''':
* SMD resistor between TX and RX pins.

''' Works with''':
* [[Digitek DT4000ZC]], [[TekPower TP4000ZC]]

''' Where to buy''':
* The cable ships with the multimeter. It's unclear whether it can be bought standalone (without DMM).

[[Digitek DT4000ZC]] photos:

<gallery>
File:Digitek dt4000zc cable front.jpg|Device, front
File:Digitek dt4000zc cable back.jpg|Device, back
File:Digitek dt4000zc cable open.jpg|Device, open
File:Digitek dt4000zc cable open2.jpg|Device, open 2
File:Digitek dt4000zc cable resistor.jpg|Resistor
</gallery>

[[TekPower TP4000ZC]] photos:

<gallery>
File:Tp4000zc_232_cable.jpg|Supplied RS-232 cable
File:Tp4000zc_232_cable_open.jpg|RS-232 cable, disassembled
File:Tp4000zc_232_cable_detail.jpg|RS-232 cable, detail
</gallery>

== Fluke IR189USB ==

The [http://www.flukeonlinestore.com/2428108.html Fluke IR189USB] is a USB interface cable for Fluke-18x and 28x series DMMs. It is a basic USB-serial cable, based on the [http://www.ftdichip.com/Products/ICs/FT232R.htm FTDI FT232RL] chip.

<gallery>
File:Fluke IR189USB.jpg
File:Fluke IR189USB bottom.jpg
File:Fluke IR189USB PCB top.jpg
File:Fluke IR189USB PCB bottom.jpg
</gallery>

== Fluke OC4USB ==

The [http://www.flukeonlinestore.com/2166266.html Fluke OC4USB] is a USB interface cable for the Fluke 120 series, 190 series scope meter, and the 430 series power quality analyzer.

Resources:
* [http://omapalvelin.homedns.org/fluke/ DIY optical link cable for the Fluke Scopemeter 190 series]

== Fluke PM9080 ==

The [http://www.flukeonlinestore.com/1641983.html Fluke PM9080] is an RS232 interface cable for "digital hard-copy output to serial printer or remote control via a PC".

The max. supported baud rate is 57600.

'''Hardware''':
No active components are on the PCB.

Pinout:
* black: pin 2 (RX)
* brown: pin 3 (TX)
* red: pin 7, 8 (RTS, CTS)
* orange: pin 1, 4, 6 (DCD, DTR, DSR)
* yellow: pin 5 (GND)

''' Works with''':
* Fluke scope meter test tools, power harmonics analyzers, graphical multimeters and multifunction counters.

'''Where to buy''':
* [http://www.flukeonlinestore.com/1641983.html flukeonlinestore.com] ($185.95)
* [http://www.fluke.eu/comx/show_product.aspx?locale=dede&pid=31870 fluke.eu] (€240.-)
* [http://de.farnell.com/fluke/pm9080/pm9080-rs-232-adapter-kabel-optisch/dp/252384 Farnell] (€240.-)
* [http://www.instrumentation2000.com/flukepm9080opticallyisolatedrs-232adaptercable.aspx instrumentation2000.com] ($187.95)
* [http://de.rs-online.com/web/p/interface-adapter/4256752/ RS-Online] (€245.-)
* [http://www.amazon.com/Fluke-PM9080-101-Optically-Isolated/dp/B000LEDHHS Amazon] ($168.23)

'''Resources''':
* [http://omapalvelin.homedns.org/fluke/ DIY optical link cable for the Fluke Scopemeter 190 series]
* [http://www.scopemeter.com/accessories/PM9080.htm PM9080 Optically-isolated RS-232C Interface Adapter] (comparison of the different cable revisions)

<gallery>
File:Fluke PM9080 top.jpg
File:Fluke PM9080 bottom.jpg
File:Fluke PM9080 LEDs.jpg
File:Fluke PM9080 PCB top.jpg
File:Fluke PM9080 PCB bottom.jpg
</gallery>

== Gossen Metrawatt ==
See [[Gossen Metrawatt#Communication Hardware|Gossen Metrawatt]] page.

== GreenLee DMSC-9U ==

TODO.

'''Hardware''':
* TODO.

''' Works with''':
* GreenLee DM-800 series, DML-430A

''' Where to buy''':
* TODO.

== Metex 5-pin RS232 cable ==

This type of 5-pin RS232 cable is used in various Metex (and rebadged) multimeters.

The cable exists in two flavours, an older version with equal pin distance (can be inserted the wrong way) and a newer version with a gap between pins 3 and 4 (fits only one way).

=== Version 1 ===
'''Hardware''':
* No active components.
* 25-pin RS232 connector

''' Works with''':
* [[Voltcraft M-3650CR]], [[PeakTech 4380]], many others.

''' Where to buy''':
* The cable ships with the respective multimeter. It's unclear whether it can be bought standalone (without DMM).

<gallery>
File:PeakTech 4380 cable.jpg|25-pin RS-232 cable
File:PeakTech 4380 cable open.jpg|DB-25F opened, wiring
</gallery>

=== Version 2 ===
'''Hardware''':
* No active components.
* 9-pin RS232 connector

''' Works with''':
* [[MASTECH MAS345]], [[Voltcraft M-3650CR]] (plug with equal pin distances!), [[RadioShack 22-168]], [[Voltcraft M-3650D]], many others.

''' Where to buy''':
* The cable ships with the respective multimeter. It's unclear whether it can be bought standalone (without DMM).

[[MASTECH MAS345]]:
<gallery>
File:Mastech mas345 rs232 cable.jpg|Cable
File:Mastech mas345 rs232 cable connected.jpg|Cable, connected
</gallery>

[[RadioShack 22-168]]:
<gallery>
File:Rs_22_168_cable.jpg|RS-232 cable
File:Rs_22_168_cable_dmm_end.jpg|DMM connector
File:Rs_22_168_cable_dmm_end_exposed.jpg|DMM connector, protective sheath removed
File:Rs_22_168_cable_internals.jpg|DB9 connector, opened
File:Rs_22_168_cable_connection.jpg|DB9 connections
</gallery>

'''DIY:'''
<gallery>
File:MetexDIY.JPG|DIY adapter
File:MetexAnschluss.JPG|Pin numbers (Metex DMM)
</gallery>

=== Cable pinout ===
{| border="0" style="font-size: smaller;" class="alternategrey sigroktable"
!Metex-connector pin (male)
!RS-232 25-pin female
!RS-232 DE9-female pin
!Signal (computer side)
!Remarks
|-
| 1 || 7 || 5 || GND ||
|-
| 2 || 2 || 3 || TX ||
|-
| 3 || 4 || 7 || RTS || Used to power receiver in multimeter, must be OFF.
|-
| 4 ||20 || 4 || DTR || Used to power receiver in multimeter, must be ON.
|-
| 5 || 3 || 2 || RX ||
|}

== UNI-T UT-D02 ==

The [http://www.uni-trend.com/en/product/2014_0626_553.html UNI-T UT-D02] is an RS232 cable for various UNI-T multimeters (and rebranded models) with PC connectivity.

'''Hardware''':
* TODO.

''' Works with''':
* UNI-T UT61D/...
* Voltcraft VC820/VC840/...

''' Where to buy''':
* [https://secure.reichelt.de/Multimeter-digital/UT-D01/3/index.html?;ACTION=3;LA=2;ARTICLE=100496;GROUPID=4058;artnr=UT+D01 Reichelt] (€15.95)
* [http://www.conrad.de/ce/de/product/125640/VOLTCRAFT-RS-232-SCHNITTSTELLENADAPTER/SHOP_AREA_17626&promotionareaSearchDetail=005 Conrad/Voltcraft] (€9.95)
* [http://www.pinsonne-elektronik.de/pi10/pd82.html Pinnesonne] (€5.00)
* [http://www.ebay.de/itm/UNI-T-UT-D02-RS232-Data-Cable-/360492337424 eBay, various sellers] (€7.99)

<gallery>
File:Voltcraft dmm rs232 cable.jpg|Cable
File:Voltcraft dmm rs232 cable ir.jpg|Cable, IR
File:Voltcraft dmm rs232 cable open.jpg|Cable, open
File:Voltcraft dmm rs232 cable pcb front.jpg|PCB, front
File:Voltcraft dmm rs232 cable pcb back.jpg|PCB, back
</gallery>

== UNI-T UT-D04 ==

The [http://www.uni-trend.com/UT-D04.html UNI-T UT-D04] (see also [http://www.uni-trend.com.cn/cp-show.asp?yy=%D6%D0%CE%C4&ProductNO=386 uni-trend.com.cn]) is a USB/HID cable for various UNI-T multimeters (and rebranded models) with PC connectivity.

There have been (at least) two versions of this cable, the older one with Hoitek HE2325U USB/HID chip, the newer one using a WCH CH9325 USB/HID chip.

See [[Device cables/Info#UNI-T_UT-D04]] for more details (such as '''lsusb -v''' output) about the cable.

'''Hardware (old version)''':
* Hoitek HE2325U

'''Hardware (new version)''':
* [[WCH CH9325]]

'''Works with''':
* [[UNI-T UT61B]] / [[UNI-T UT61C|UT61C]] / [[UNI-T UT61D|UT61D]] / [[UNI-T UT61E|UT61E]], various other UNI-T DMMs
* [[Voltcraft VC-820]] / [[Voltcraft VC-830|VC-830]] / [[Voltcraft VC-840|VC-840]], various other Voltcraft rebadges of UNI-T DMMs
* [[Tenma 72-7745]] and various other Tenma/Farnell rebadges of UNI-T DMMs

'''Where to buy''':
* [https://secure.reichelt.de/Multimeter-digital/UT-D04/3/index.html?;ACTION=3;LA=2;ARTICLE=97153;GROUPID=4058;artnr=UT+D04 Reichelt] (€9.95)
* [http://www.conrad.de/ce/de/product/120317/Voltcraft-USB-SCHNITTSTELLENADPTER/SHOP_AREA_17626&promotionareaSearchDetail=005 Conrad/Voltcraft] (€25.95)
* [http://www.pinsonne-elektronik.de/pi10/pd78.html Pinnesonne] (€8.90)
* [http://www.ebay.de/itm/UT-D04-USB-INFRARED-INTERFACE-CABLE-FOR-UT71-and-UT81-/180687967854 eBay, various sellers] (€12.37)

<gallery>
File:Uni-t ut61d cable.jpg|Cable
File:Uni-t ut61d cable ir.jpg|Cable, IR
File:Uni-t ut61d usb cable attached.jpg|Attached cable
File:Uni-t ut61d cable open1.jpg|Opened 1
File:Uni-t ut61d cable open2.jpg|Opened 2
File:Uni-t ut61d cable pcb front.jpg|PCB, front
File:Uni-t ut61d cable pcb back.jpg|PCB, back
</gallery>

other cable, but only with different silkscreen (another batch?)

<gallery>
File:UT81-USB_cable.jpg|Cable
File:UT81-USB_cable_led.jpg|Cable, IR
File:UT81-USB_cable_opened.jpg|Opened
File:UT81-USB_cable_front.jpg|PCB, front
File:UT81-USB_cable_back.jpg|PCB, back
</gallery>

Voltcraft sells rebranded, UNI-T made DMMs, and also ships with the same USB/HID cable, but with a Voltcraft logo/marking on it. It is likely that Voltcraft also shipped both the old and new version of the cable at some point.

<gallery>
File:Voltcraft ut-d04 cable.jpg|Voltcraft cable
File:Voltcraft ut-d04 ir.jpg|Voltcraft cable, IR
</gallery>

== V&A VA4000 ==

The [http://www.mastech.com.cn/html/en/products-accessories.htm V&A VA4000] is a USB PC interface cable for various V&A multimeters.

It seems there have been at least two different revisions of the cable. The older one used a Sunplus SPCP825 USB-to-serial chip (see [http://www.mikrocontroller.net/topic/160215#2032176 here], [http://multimeter.schewe.com/ here], or also check the drivers from [http://www.elv.de/digital-multimeter-va18b-mit-pc-link.html here]), the newer revisions use a Prolific PL2303HX chip.

See [[Device cables/Info#V.26A_VA4000]] for more details (such as '''lsusb -v''' output) about the cable.

'''Hardware''' (old cable version):

* '''USB to serial chip''': Sunplus SPCP825
* '''Crystal''': ?

'''Hardware''' (new cable version):

* '''USB to serial chip''': Prolific PL2303HX YR0903A
* '''Crystal''': 12MHz

''' Works with''':
* V&A VA18B, V&A VA-38

''' Where to buy''':
* [http://www.komerci.de/shop/product_info.php?products_id=427&cPath=26_42&osCsid=0c0a8cf5d72cd931528b26aeb5af7ce5 Komerci] (€6.50)

Old cable with Sunplus SPCP825 chip from a [[V&A VA18B]]:

<gallery>
File:Va va4000 cable sunplus ic 0405.jpg|USB cable
File:Va va4000 cable sunplus ic 0407.jpg|Cable, dismantled
File:Va va4000 cable sunplus ic 0408.jpg|PCB, top
File:Va va4000 cable sunplus ic 0414.jpg|PCB, bottom
</gallery>

New cable with Prolific PL2303HX from a [[V&A VA18B]]:

<gallery>
File:Mastech va18b usb cable.jpg|USB cable
File:Mastech va18b usb cable pcb front.jpg|USB cable PCB, front
File:Mastech va18b usb cable pcb back.jpg|USB cable PCB, back
</gallery>

Another cable shipped with a [[V&A VA40B]] (it has the same Prolific PL2303HX PCB as the V&A 18B above, but seem to have a thinner mechanical plug):

<gallery>
File:VA40B USB cable.JPG|USB cable
VA40B_USB_cable_connector.JPG|USB cable, optical connector
</gallery>

== V&A VA4001 ==

The [http://www.mastech.com.cn/html/en/products-accessories.htm V&A VA4001] is an RS232 PC interface cable for various V&A multimeters.

TODO.

== Victor 86C USB cable ==

The [[Victor 86C]] PC interface cable (doesn't seem to have a specific name or part number) contains a USB/HID chip.

'''Hardware''':

* '''USB/HID chip''': [[Victor_protocol#USB_interface_chip|Unmarked SO-20 chip]]

''' Works with''':
* Victor 86C. Maybe other Victor models(?)

''' Where to buy''':
* The cable ships with the Victor 86C. It's unclear whether it can be bought standalone (without DMM).

<gallery>
File:Victor 86c usb cable.jpg|USB cable
File:Victor 86c usb cable open.jpg|USB cable, open
File:Victor 86c usb cable pcb top.jpg|USB cable PCB, front
File:Victor 86c usb cable pcb bottom.jpg|USB cable PCB, back
</gallery>

More information about the USB chip and the protocol it uses to communicate with the PC can be found on the [[Victor protocol]] page.

= Sound level meters =

== Colead SL-5868P cables ==

Some distributors sell the [[Colead SL-5868P]] sound level meter with a set of two cables: one 3.5mm jack to female DB9, and one male DB9 to USB, which has a Prolific PL-2303 chip in the DB9. This cable does not work; the device's serial port needs a 2.5mm jack.

<gallery>
File:Colead SL5868P cables.jpg|A really bad idea
File:Colead SL5868P cable USB top.jpg|DB9 to USB, top
File:Colead SL5868P cable USB bottom.jpg|DB9 to USB, bottom
File:Colead SL5868P cable serial top.jpg|3.5mm jack to DB9, top
File:Colead SL5868P cable serial bottom.jpg|3.5mm jack to DB9, bottom
</gallery>

The SL-5868P is also available with bluetooth connectivity instead of serial.

== Tondaj SL-814 cable ==

The [[Tondaj SL-814]] sound level meter ships with this USB PC interface cable.

'''Hardware''':
* '''USB to serial chip''': Prolific PL2303HX LFC10073A
* '''Crystal''': 12MHz

''' Works with''':
* [[Tondaj SL-814]] (maybe other Tondaj gear?)

''' Where to buy''':
* The cable ships with the [[Tondaj SL-814]]. It's unclear whether it can be bought standalone (without the sound level meter).

<gallery>
File:Tondaj sl814 cable.jpg|Cable
File:Tondaj sl814 cable connector.jpg|Cable, connector
File:Tondaj sl814 cable open1.jpg|Cable, open
File:Tondaj sl814 cable open2.jpg|Cable, open 2
File:Tondaj sl814 cable pcb top.jpg|PCB, top
File:Tondaj sl814 cable pcb bottom.jpg|PCB, bottom
</gallery>

= Programmable electronic loads =

== M133 ==

The '''M133''' (vendor unknown) cable ships with the [[ATTEN ATZ9711]] programmable electronic load. It's unclear whether this is a custom cable for this device, or a generic RS232 isolator cable.

The 28-pin chip is a standard Prolific PL-2303HX serial-USB chip.

The other chip is presumably an optocoupler, but the vendor/model is unknown.

<gallery>
File:M133 isolated serial-USB cable.jpg
File:M133 isolated serial-USB cable back.jpg
File:M133 isolated serial-USB cable PCB top.jpg
File:M133 isolated serial-USB cable PCB bottom.jpg
File:M133 isolated serial-USB cable chip.jpg
</gallery>

= See also =

* [[Multimeter ICs]]
* [[Serial port]]

UNI-T UT61B

2014-01-01T18:47:54Z

Tsaitgaist: /* Photos */ add scree view

{{Infobox multimeter
| image = [[File:Uni-t_ut61b_device.png|180px]]
| name = UNI-T UT61B
| status = supported
| source_code_dir = uni-t-dmm
| counts = 4000
| categories = CAT II (600V) / CAT III (300V)
| connectivity = [[Device_cables#UNI-T_UT-D02|RS232]] / [[Device_cables#UNI-T_UT-D04|USB]]
| measurements = voltage, current, resistance, capacitance, frequency, duty cycle, diode, continuity, temperature
| features = autorange, data hold, min/max, rel, bargraph, backlight
| website = [http://www.uni-trend.com/UT61B.html uni-trend.com]
}}

The '''UNI-T UT61B''' is a 4000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity.

== Hardware ==

'''Multimeter''':
* '''Multimeter IC''': [[Multimeter_ICs#Fortune_Semiconductor_FS9922-DMM3|Fortune Semiconductor FS9922-DMM3]] ([http://www.ic-fortune.com/upload/Download/FS9922-DMM3-DS-10_EN.pdf datasheet])
* '''Crystal''': 4MHz (markings: "3.999")
* '''Fuses''': 0.5A/600V and 10A/600V (HRV fuses)

'''RS232 cable''':

See [[Device cables#UNI-T_UT-D02]].

'''USB cable''':

See [[Device cables#UNI-T_UT-D04]].

to use it with this cable, run:
sigrok-cli --driver uni-t-ut61b:conn=1a86.e008 --continuous -O analog

don't forget to run the ''suspend.HE2325U.sh'' script, and enable data transmission on the DMM.

== Photos ==

'''Multimeter''':

<gallery>
File:Uni-t_ut61b_device.png|Device, front
File:Uni-t_ut61b_back.jpg|Device, back
File:Uni-t_ut61b_battery.jpg|Battery
File:Uni-t ut61b_inside-back.jpg|Device open back
File:Uni-t_ut61b_inside-front.jpg|Device open front
File:Uni-t_ut61b_pcb-front.jpg|PCB, front
File:Uni-t_ut61b_pcb-back.jpg|PCB, back
File:Uni-t_ut61b_screen.jpg|screen
</gallery>

'''RS232 cable''':

See [[Device cables#UNI-T_UT-D02]].

'''USB cable''':

See [[Device cables#UNI-T_UT-D04]].

== Protocol ==

See [[Multimeter_ICs#Fortune_Semiconductor_FS9922-DMM3]] for the DMM IC protocol. Depending on the cable, additional transport-specific decoding is needed, though.

== Resources ==

* [http://www.uni-trend.com/manual2/UT61English.pdf Manual]
* [http://www.uni-trend.com/Web%20site/DMM%20Software/UT61B%20setup.exe Vendor software]
* [https://perhof.wordpress.com/category/computing/linux/ perhof: Uni-T UT61D for Linux] (also: [http://dl.dropbox.com/u/20603229/published/ut61d.zip ut61d.zip])

[[Category:Device]]
[[Category:Multimeter]]
[[Category:Supported]]

File:Uni-t ut61b screen.jpg

2014-01-01T18:47:05Z

Tsaitgaist: UNI-T UT61B DMM screen view

== Summary ==
UNI-T UT61B DMM

screen view
== Licensing ==
{{CC-BY-SA-3.0}}

UNI-T UT61B

2014-01-01T18:37:14Z

Tsaitgaist: add howto use it with sigrok

{{Infobox multimeter
| image = [[File:Uni-t_ut61b_device.png|180px]]
| name = UNI-T UT61B
| status = supported
| source_code_dir = uni-t-dmm
| counts = 4000
| categories = CAT II (600V) / CAT III (300V)
| connectivity = [[Device_cables#UNI-T_UT-D02|RS232]] / [[Device_cables#UNI-T_UT-D04|USB]]
| measurements = voltage, current, resistance, capacitance, frequency, duty cycle, diode, continuity, temperature
| features = autorange, data hold, min/max, rel, bargraph, backlight
| website = [http://www.uni-trend.com/UT61B.html uni-trend.com]
}}

The '''UNI-T UT61B''' is a 4000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity.

== Hardware ==

'''Multimeter''':
* '''Multimeter IC''': [[Multimeter_ICs#Fortune_Semiconductor_FS9922-DMM3|Fortune Semiconductor FS9922-DMM3]] ([http://www.ic-fortune.com/upload/Download/FS9922-DMM3-DS-10_EN.pdf datasheet])
* '''Crystal''': 4MHz (markings: "3.999")
* '''Fuses''': 0.5A/600V and 10A/600V (HRV fuses)

'''RS232 cable''':

See [[Device cables#UNI-T_UT-D02]].

'''USB cable''':

See [[Device cables#UNI-T_UT-D04]].

to use it with this cable, run:
sigrok-cli --driver uni-t-ut61b:conn=1a86.e008 --continuous -O analog

don't forget to run the ''suspend.HE2325U.sh'' script, and enable data transmission on the DMM.

== Photos ==

'''Multimeter''':

<gallery>
File:Uni-t_ut61b_device.png|Device, front
File:Uni-t_ut61b_back.jpg|Device, back
File:Uni-t_ut61b_battery.jpg|Battery
File:Uni-t ut61b_inside-back.jpg|Device open back
File:Uni-t_ut61b_inside-front.jpg|Device open front
File:Uni-t_ut61b_pcb-front.jpg|PCB, front
File:Uni-t_ut61b_pcb-back.jpg|PCB, back
</gallery>

'''RS232 cable''':

See [[Device cables#UNI-T_UT-D02]].

'''USB cable''':

See [[Device cables#UNI-T_UT-D04]].

== Protocol ==

See [[Multimeter_ICs#Fortune_Semiconductor_FS9922-DMM3]] for the DMM IC protocol. Depending on the cable, additional transport-specific decoding is needed, though.

== Resources ==

* [http://www.uni-trend.com/manual2/UT61English.pdf Manual]
* [http://www.uni-trend.com/Web%20site/DMM%20Software/UT61B%20setup.exe Vendor software]
* [https://perhof.wordpress.com/category/computing/linux/ perhof: Uni-T UT61D for Linux] (also: [http://dl.dropbox.com/u/20603229/published/ut61d.zip ut61d.zip])

[[Category:Device]]
[[Category:Multimeter]]
[[Category:Supported]]

Supported hardware

2014-01-01T18:31:09Z

Tsaitgaist: add UNI-T UT61B

sigrok is intended as a flexible, cross-platform, and '''hardware-independent''' software suite, i.e., it supports various devices from many different vendors.

Here is a list of currently supported devices (various stages of completeness) and devices we plan to support in the near future.

The lists are sorted by category (supported: [[:Category:Supported|{{PAGESINCATEGORY:Supported|pages}}]], in progress: [[:Category:In progress|{{PAGESINCATEGORY:In progress|pages}}]], planned: [[:Category:Planned|{{PAGESINCATEGORY:Planned|pages}}]]), and alphabetically within those categories.

== Logic analyzers ==

<gallery widths="100px" heights="100px">
File:ARMFLY MINI LOGIC.png|[[File:Nuvola OK.png|16px]] [[ARMFLY Mini-Logic]] (8ch, 24MHz)
File:Sigma2_2.png|[[File:Nuvola OK.png|16px]] [[ASIX SIGMA]] (16ch, 200MHz)
File:Braintechnology_usb_interface_v26.png|[[File:Nuvola OK.png|16px]] [[Braintechnology USB Interface V2.x]] (8/16ch, 24/12MHz)
File:Braintechnology_usb_lps.png|[[File:Nuvola OK.png|16px]] [[Braintechnology USB-LPS]] (8/16ch, 24/12MHz)
File:Chronovu la8 front.png|link=ChronoVu LA8|[[File:Nuvola OK.png|16px]] [[ChronoVu LA8]] (8ch, 100MHz)
File:Cwav_usbee_sx.png|[[File:Nuvola OK.png|16px]] [[CWAV USBee SX]] (8ch, 100MHz)
File:Buspirate_v3.png|[[File:Nuvola OK.png|16px]] [[Dangerous Prototypes Buspirate]] (5ch, 1MHz)
File:Eeelec xla esla100.png|[[File:Nuvola OK.png|16px]] [[EE Electronics ESLA100]] (8ch, 24MHz)
File:Ikalogic_scanalogic2.png|[[File:Nuvola OK.png|16px]] [[IKALOGIC Scanalogic-2]] (4ch, 20MHz)
File:Ikalogic scanaplus mugshot.png|[[File:Nuvola OK.png|16px]] [[IKALOGIC ScanaPLUS]] (9ch, 100MHz)
File:Kingst kqs3506 la16100.png|[[File:Nuvola OK.png|16px]] [[KingST KQS3506-LA16100]] (16ch, 100/50/32/16MHz @ 3/6/9/16ch)
File:Lcsoft-miniboard-front.png|[[File:Nuvola OK.png|16px]] [[Lcsoft Mini Board]] (8/16ch, 24/12MHz)
File:logic-shrimp-front.png|[[File:Nuvola OK.png|16px]] [[Logic Shrimp]] (4ch, 20MHz)
File:Mcu123 saleae logic clone.png|[[File:Nuvola OK.png|16px]] [[MCU123 Saleae Logic clone]] (8ch, 24MHz)
File:Usbee_ax_clone_front.png|[[File:Nuvola OK.png|16px]] [[MCU123 USBee AX Pro clone]] (8ch, 24MHz)
File:Openbench logic sniffer front.png|[[File:Nuvola OK.png|16px]] [[Openbench Logic Sniffer]] (32ch, 100MHz)
File:Robomotic buglogic3.png|[[File:Nuvola OK.png|16px]] [[Robomotic BugLogic 3]] (8ch, 24MHz)
File:Robomotic_minilogic.png|[[File:Nuvola OK.png|16px]] [[Robomotic MiniLogic]] (8ch, 24MHz)
File:Saleae Logic.png|[[File:Nuvola OK.png|16px]] [[Saleae Logic]] (8ch, 24MHz)
File:Saleae_Logic16_bottom.png|[[File:Nuvola OK.png|16px]] [[Saleae Logic16]] (16ch, 100/50/32/16MHz @ 3/6/9/16ch)
File:Wayengineer saleae16.png|[[File:Nuvola OK.png|16px]] [[WayEngineer Saleae16]] (16ch, 100/50/32/16MHz @ 3/6/9/16ch)
File:Zeroplus Logic Cube.png|[[File:Nuvola OK.png|16px]] [[ZEROPLUS Logic Cube LAP-C(16032)]] (16ch, 100MHz)
File:Zeroplus_lap-16128u.png|[[File:Nuvola OK.png|16px]] [[ZEROPLUS LAP-16128U]] (16ch, 200MHz)

File:Chronovu la16.png|[[File:Nuvola Orange.png|16px]] [[ChronoVu LA16]] (16ch, 200MHz)
File:Rockylogic_ant8.png|[[File:Nuvola Orange.png|16px]] [[RockyLogic Ant8]] (8ch, 500MHz)
File:RockyLogic Ant18e.png|[[File:Nuvola Orange.png|16px]] [[RockyLogic Ant18e]] (8ch, 1GHz)
File:Sysclk lwla1034.jpg|[[File:Nuvola Orange.png|16px]] [[Sysclk LWLA1034]] (34ch, 125MHz)

File:Acute_pkla1216.png|[[File:Nuvola Red.png|16px]] [[Acute PKLA-1216]] (16ch, 200MHz)
File:Hantek4032L_BoxSideView.png|[[File:Nuvola Red.png|16px]] [[Hantek 4032L]] (32ch, 400MHz)
File:Ideofy_la_08.png|[[File:Nuvola Red.png|16px]] [[Ideofy LA-08]] (8ch, 96/60/30MHz @ 2/4/8ch)
File:Intronix Logicport.png|[[File:Nuvola Red.png|16px]] [[Intronix Logicport LA1034]] (34ch, 500MHz)
File:Sigrok_logo_no_text_transparent_512.png|[[File:Nuvola Red.png|16px]] [[Link Instruments LA-5580]] (80ch, 500MHz)
File:Microchip_pickit2.png|[[File:Nuvola Red.png|16px]] [[Microchip PICkit2]] (3ch, 1MHz)
File:Minila parport.png|[[File:Nuvola Red.png|16px]] [[MiniLA]] (32ch, 100MHz)
File:Minila_mockup.png|[[File:Nuvola Red.png|16px]] [[MiniLA Mockup]] (32ch, 100MHz)
File:Sysclk lwla1016.png|[[File:Nuvola Red.png|16px]] [[Sysclk LWLA1016]] (16ch, 100MHz)
File:Techtools_digiview_dv1-100.png|[[File:Nuvola Red.png|16px]] [[TechTools DigiView DV1-100]] (18ch, 100MHz)
File:Xmos xtag2.png|[[File:Nuvola Red.png|16px]] [[XMOS XTAG-2]] (?ch, 50MHz)
File:Sigrok_logo_no_text_transparent_512.png|[[File:Nuvola Red.png|16px]] [[ZEROPLUS Logic Cube LAP-C(322000)]] (32ch, 200MHz)
File:Zlg_la1032.png|[[File:Nuvola Red.png|16px]] [[ZLG LA1032]] (32ch, 100MHz)
</gallery>

== Mixed-signal devices ==

<gallery widths=105px heights=105px>
File:Armfly_ax_pro.png|[[File:Nuvola OK.png|16px]] [[ARMFLY AX-Pro]]1 (8ch, 24MHz; 2ch analog, 24MSa/s, 40MHz BW)
File:Esla201a.png|[[File:Nuvola OK.png|16px]] [[EE Electronics ESLA201A]]1 (8ch, 24MHz; 2ch analog, 24MSa/s, 40MHz BW)
File:Studio_XZL_AX.jpeg|[[File:Nuvola OK.png|16px]] [[XZL_Studio AX]]1 (8ch, 24MHz; 2ch analog, 24MSa/s, 40MHz BW)

File:BitScope BS10.png|[[File:Nuvola Orange.png|16px]] [[BitScope BS10]] (8ch, 40MHz; 2ch analog, 20MSa/s, ? BW)
File:Link Instruments MSO-19 front.png|[[File:Nuvola Orange.png|16px]] [[Link Instruments MSO-19]] (8ch, 200MHz; 1ch analog, 200MSa/s, 60MHz BW)

File:Agilent_MSO7104A.png|[[File:Nuvola Red.png|16px]] [[Agilent MSO7104A]] (16ch, ?; 4ch analog, 2GSa/s, 100MHz BW)
File:Digilent_analog_discovery.png|[[File:Nuvola Red.png|16px]] [[Digilent Analog Discovery]] (16ch, 100MHz; 2ch analog, 100MSa/s, 5MHz BW)
File:Hantek_1008C.png|[[File:Nuvola Red.png|16px]] [[Hantek 1008C]] (8ch)
File:Meilhaus_mephisto_scope1.png|[[File:Nuvola Red.png|16px]] [[Meilhaus MEphisto Scope1]] (16ch, 100kHz; 2ch analog, 1MSa/s, 500kHz BW)
File:Polabs_poscope_basic2.png|[[File:Nuvola Red.png|16px]] [[PoLabs PoScope Basic2]] (16ch, 8MHz; 2ch analog, 200kSa/s, ? BW)
File:QA100.png|[[File:Nuvola Red.png|16px]] [[QuantAsylum QA100]] (12ch; 2ch analog)
File:Rigol_VS5202D.png|[[File:Nuvola Red.png|16px]] [[Rigol VS5202D]] (16ch, 200MHz; 2ch analog)
File:Sigrok_logo_no_text_transparent_512.png|[[File:Nuvola Red.png|16px]] [[XZL_Studio DX]] (16ch, 24MHz; 2ch analog)
</gallery>


1 Only the logic analyzer functionality is supported so far, analog support is work in progress. 


== Oscilloscopes ==

<gallery widths=100px heights=100px>
File:Agilent DSO1014A.png|link=Agilent DSO1014A|[[File:Nuvola OK.png|16px]] [[Agilent DSO1014A]] (4ch, 2GS/s, 100MHz BW)
File:Fluke_Scopemeter_199B.png|link=Fluke ScopeMeter 199B|[[File:Nuvola OK.png|16px]] [[Fluke ScopeMeter 199B]] (2ch, 2.5GS/s, 200MHz BW)
File:Hameg hmo1524.png|link=Hameg HMO1524|[[File:Nuvola OK.png|16px]] [[Hameg HMO1524]] (4ch, 2GS/s, 150MHz BW)
File:Hameg HMO2024.png|link=Hameg HMO2024|[[File:Nuvola OK.png|16px]] [[Hameg HMO2024]] (4ch, 2GS/s, 200MHz BW)
File:Hantek DSO-2090.png|link=Hantek DSO-2090|[[File:Nuvola OK.png|16px]] [[Hantek DSO-2090]] (2ch, 100MS/s, 40MHz)
File:Rigol DS1052E.png|link=Rigol DS1052E|[[File:Nuvola OK.png|16px]] [[Rigol DS1052E]] (2ch, 1GS/s, 50MHz BW)
File:Rigol ds1102e.png|link=Rigol DS1102E|[[File:Nuvola OK.png|16px]] [[Rigol DS1102E]] (2ch, 1GS/s, 100MHz BW)

File:Focussz_fosc21_mugshot.png|link=Focussz Fosc21|[[File:Nuvola Orange.png|16px]] [[Focussz Fosc21]] (2ch, 8kS/s, 3kHz BW)
File:Dso2250-top.png|link=Hantek DSO-2250|[[File:Nuvola Orange.png|16px]] [[Hantek DSO-2250]] (2ch, 250MS/s, 100MHz BW)
File:Hantek dso-5200a device front.png|link=Hantek DSO-5200A|[[File:Nuvola Orange.png|16px]] [[Hantek DSO-5200A]] (2ch, 250MS/s, 200MHz BW)
File:OsciPrime.png|link=Nexus-Computing OsciPrime|[[File:Nuvola Orange.png|16px]] [[Nexus-Computing OsciPrime]] (2ch, ?MS/s, 3.3MHz-8MHz BW)
File:Velleman PCSU1000.png|link=Velleman PCSU1000|[[File:Nuvola Orange.png|16px]] [[Velleman PCSU1000]] (2ch, 1GS/s, 50MHz BW)

File:Sigrok_logo_no_text_transparent_512.png|link=Hantek DSO-1200|[[File:Nuvola Red.png|16px]] [[Hantek DSO-1200]] (2ch, 500MS/s, 200MHz BW)
File:Fluke scopemeter123.png|link=Fluke ScopeMeter 123|[[File:Nuvola Red.png|16px]] [[Fluke ScopeMeter 123]] (2ch, 25MS/s, 20MHz BW)
File:Picoscope 2203.png|link=Pico Technology PicoScope 2203|[[File:Nuvola Red.png|16px]] [[Pico Technology PicoScope 2203]] (40/20MS/s, 5MHz BW)
File:PicoScope_2205.png|link=Pico Technology PicoScope 2205|[[File:Nuvola Red.png|16px]] [[Pico Technology PicoScope 2205]] (200/100MS/s, 25MHz BW)
File:Picoscope 3206.png|link=Pico Technology PicoScope 3206|[[File:Nuvola Red.png|16px]] [[Pico Technology PicoScope 3206]] (200/100MS/s, 200MHz BW)
File:Picoscope 5203.png|link=Pico Technology PicoScope 5203|[[File:Nuvola Red.png|16px]] [[Pico Technology PicoScope 5203]] (1/0.5GS/s, 250MHz BW)
File:Usbduxfast.png|link=Incite Technology USB-DUXfast|[[File:Nuvola Red.png|16px]] [[Incite Technology USB-DUXfast]] (16ch, 3MHz, ? BW)
File:UNI-T UTD2042C.png|link=UNI-T UTD2042C|[[File:Nuvola Red.png|16px]] [[UNI-T UTD2042C]] (2ch, 500MS/s, 40MHz BW)
File:Voltcraft dso-220 usb.png|link=Voltcraft DSO-220|[[File:Nuvola Red.png|16px]] [[Voltcraft DSO-220]] (2ch, 60MS/s, 20MHz BW)
File:Voltcraft DSO-3062C.png|link=Voltcraft DSO-3062C|[[File:Nuvola Red.png|16px]] [[Voltcraft DSO-3062C]] (2ch, 1GS/s, 60MHz BW)
File:Rigol_DS2072.png|link=Rigol DS2072|[[File:Nuvola Red.png|16px]] [[Rigol DS2072]] (2ch, 2GS/s, 70MHz BW)
</gallery>

== Multimeters ==

<gallery widths="100px" heights="100px">
File:Sigrok_logo_no_text_transparent_512.png|link=Agilent U1231A|[[File:Nuvola OK.png|16px]] [[Agilent U1231A]] (6000 counts, USB/Bluetooth)
File:Agilent U1232A.png|[[File:Nuvola OK.png|16px]] [[Agilent U1232A]] (6000 counts, USB/Bluetooth)
File:Sigrok_logo_no_text_transparent_512.png|[[File:Nuvola OK.png|16px]] [[Agilent U1233A]] (6000 counts, USB/Bluetooth)
File:Sigrok_logo_no_text_transparent_512.png|[[File:Nuvola OK.png|16px]] [[BBC Goertz Metrawatt M2110]] (30000 counts, RS232)
File:Bm_857_mugshot_500000.png|[[File:Nuvola OK.png|16px]] [[Brymen BM857]] (50000 counts, RS232)
File:Digitek_dt4000zc_device_front.png|[[File:Nuvola OK.png|16px]] [[Digitek DT4000ZC]] (4000 counts, RS232)
File:Fluke 187.png|[[File:Nuvola OK.png|16px]] [[Fluke 187/189]] (50000 counts, RS232)
File:Fluke 287.png|[[File:Nuvola OK.png|16px]] [[Fluke 287/289]] (50000 counts, RS232)
File:Gossen Metrawatt Metrahit 16I small.png|[[File:Nuvola OK.png|16px]] [[Gossen Metrawatt Metrahit 16I]] (3100 counts, RS232)
File:Gossen Metrawatt Metrahit 18S small.png|[[File:Nuvola OK.png|16px]] [[Gossen Metrawatt Metrahit 18S]] (31000 counts, RS232)
File:100px_Idm103n.png|[[File:Nuvola OK.png|16px]] [[ISO-TECH IDM103N]] (4000 counts, RS232)
File:Mastech mas345 device front.png|[[File:Nuvola OK.png|16px]] [[MASTECH MAS345]] (4000 counts, RS232)
File:Metex m4650cr mugshot.png|[[File:Nuvola OK.png|16px]] [[Metex M-4650CR]] (20000 counts, RS232)
File:Norma dm950.png|[[File:Nuvola OK.png|16px]] [[Norma DM950]] (21000 counts, RS232)
File:Pce-pce-dm32.png|[[File:Nuvola OK.png|16px]] [[PCE PCE-DM32]] (4000 counts, RS232)
File:Metex_me-31.png|[[File:Nuvola OK.png|16px]] [[PeakTech 3410]] (4000 counts, RS232)
File:Peaktech 4370 device front.png|[[File:Nuvola OK.png|16px]] [[PeakTech 4370]] (2000 counts, RS232)
File:Rs_22_168_mugshot.png|[[File:Nuvola OK.png|16px]] [[RadioShack 22-168]] (2000 counts, RS232)
File:Rs_22-805_front.png|[[File:Nuvola OK.png|16px]] [[RadioShack 22-805]] (4000 counts, RS232)
File:radioshack_22_812_front.png|[[File:Nuvola OK.png|16px]] [[RadioShack 22-812]] (4000 counts, RS232)
File:Siemens B1105 small.png|[[File:Nuvola OK.png|16px]] [[Siemens B1105]] (310000 counts, RS232)
File:Tecpel dmm8061.png|[[File:Nuvola OK.png|16px]] [[Tecpel DMM-8061]] (4000 counts, RS232/USB)
File:Tp4000zc_front.png|[[File:Nuvola OK.png|16px]] [[TekPower TP4000ZC]] (4000 counts, RS232)
File:Tenma 72-7745.png|[[File:Nuvola OK.png|16px]] [[Tenma 72-7745]] (4000 counts, RS232/USB)
File:Ut60e_-_front_-_alpha.png|[[File:Nuvola OK.png|16px]] [[UNI-T UT60E]] (4000 counts, RS232/USB)
File:Uni-t_ut61b_device.png|[[File:Nuvola OK.png|16px]] [[UNI-T UT61B]] (4000 counts, RS232/USB)
File:Uni-t ut61c mugshot.png|[[File:Nuvola OK.png|16px]] [[UNI-T UT61C]] (6000 counts, RS232/USB)
File:Uni t ut61d device.png|[[File:Nuvola OK.png|16px]] [[UNI-T UT61D]] (6000 counts, RS232/USB)
File:Old ver front.png|[[File:Nuvola OK.png|16px]] [[UNI-T UT61E]] (22000 counts, RS232/USB)
File:Va_va18b.png|[[File:Nuvola OK.png|16px]] [[V&A VA18B]] (6000 counts, USB)
File:Victor 86c device front.png|[[File:Nuvola OK.png|16px]] [[Victor 86C]] (4000 counts, USB)
File:Victor 70C.png|[[File:Nuvola OK.png|16px]] [[Victor 70C]] (4000 counts, USB)
File:Voltcraft_M-3650D_transparent.png|[[File:Nuvola OK.png|16px]] [[Voltcraft M-3650D]] (2000 counts, RS232)
File:Voltcraft m4650cr.png|[[File:Nuvola OK.png|16px]] [[Voltcraft M-4650CR]] (20000 counts, RS232)
File:Voltcraft vc820 device.png|[[File:Nuvola OK.png|16px]] [[Voltcraft VC-820]] (4000 counts, RS232/USB)
File:Voltcraft vc830.png|[[File:Nuvola OK.png|16px]] [[Voltcraft VC-830]] (6000 counts, RS232/USB)
File:Voltcraft vc840 device front.png|[[File:Nuvola OK.png|16px]] [[Voltcraft VC-840]] (4000 counts, RS232/USB)

File:Tenma 72-1016.png|[[File:Nuvola Orange.png|16px]] [[Tenma 72-1016]] (6000 counts, RS232/USB)
File:Tenma 72-7730.png|[[File:Nuvola Orange.png|16px]] [[Tenma 72-7730]] (20000 counts, RS232/USB)
File:Tenma 72-7732.png|[[File:Nuvola Orange.png|16px]] [[Tenma 72-7732]] (40000 counts, RS232/USB)
File:Tenma 72-7750.png|[[File:Nuvola Orange.png|16px]] [[Tenma 72-7750]] (6000 counts, RS232/USB)
File:Tenma 72-9380A.png|[[File:Nuvola Orange.png|16px]] [[Tenma 72-9380A]] (40000 counts, RS232/USB)
File:Voltcraft m-3650cr.png|[[File:Nuvola Orange.png|16px]] [[Voltcraft M-3650CR]] (2000 counts, RS232)

File:Appa 107.png|[[File:Nuvola Red.png|16px]] [[APPA 107]] (4000 / 20000 counts, RS232)
File:Digitek dt8000.png|[[File:Nuvola Red.png|16px]] [[Digitek DT8000]] (8000 counts, RS232)
File:Digitek dt80000.png|[[File:Nuvola Red.png|16px]] [[Digitek DT80000]] (80000 counts, RS232)
File:Escort 179 device front.png|[[File:Nuvola Red.png|16px]] [[Escort 179]] (10000 counts, RS232)
File:Gossen metrahit 30m.png|[[File:Nuvola Red.png|16px]] [[Gossen-Metrawatt METRAHIT 30M]] (1200000 counts, RS232/USB)
File:800px-Mastech m9803r device front.png|[[File:Nuvola Red.png|16px]] [[MASTECH M9803R]] (4000 counts, RS232)
File:Metrix mx53.png|[[File:Nuvola Red.png|16px]] [[Metrix MX53]] (50000 counts, RS232)
File:Metrix mx56c.png|[[File:Nuvola Red.png|16px]] [[Metrix MX56C]] (50000 counts, RS232)
File:Sigrok_logo_no_text_transparent_512.png|[[File:Nuvola Red.png|16px]] [[Protek 6500]] (50000 counts, RS232)
File:Voltcraft m3890dt usb.png|[[File:Nuvola Red.png|16px]] [[Voltcraft M-3890DT]] (4000 counts, USB)
File:Voltcraft m4660a device front.png|[[File:Nuvola Red.png|16px]] [[Voltcraft M-4660A]] (20000 counts, RS232)
File:Voltcraft vc920.png|[[File:Nuvola Red.png|16px]] [[Voltcraft VC-920]] (40000/4000 counts, RS232/USB)
File:Voltcraft vc940.png|[[File:Nuvola Red.png|16px]] [[Voltcraft VC-940]] (40000/4000 counts, RS232/USB)
</gallery>

== LCR meters ==

TODO.

== Sound level meters ==

<gallery widths="100px" heights="100px">
File:CEM DT-8852.png|link=CEM DT-8852|[[File:Nuvola OK.png|16px]] [[CEM DT-8852]] (USB)
File:Colead SL-5868P.png|link=Colead SL-5868P|[[File:Nuvola OK.png|16px]] [[Colead SL-5868P]] (RS232)
File:Kecheng KC-330B.png|link=Kecheng KC-330B|[[File:Nuvola OK.png|16px]] [[Kecheng KC-330B]] (RS232)
File:Tondaj sl-814.png|link=Tondaj SL-814|[[File:Nuvola OK.png|16px]] [[Tondaj SL-814]] (USB)
File:Voltcraft_DL-161S.png|link=Voltcraft DL-161S|[[File:Nuvola Orange.png|16px]] [[Voltcraft DL-161S]] (USB)
File:Pce_pce-222_front.png|link=PCE PCE-222|[[File:Nuvola Red.png|16px]] [[PCE PCE-222]] (also: light-/thermo-/hygrometer; RS232)
File:Voltcraft_dl_160s.png|link=Voltcraft DL-160S|[[File:Nuvola Red.png|16px]] [[Voltcraft DL-160S]] (USB)
</gallery>

== Thermometers ==

<gallery widths="100px" heights="100px">
File:EL-USB-2.png|link=Lascar Electronics EL-USB-2|[[File:Nuvola OK.png|16px]] [[Lascar Electronics EL-USB-2]] (1xtemp, 1xhum, USB)
File:Mic 98581.png|link=MIC 98581|[[File:Nuvola OK.png|16px]] [[MIC 98581]] (1xtemp, USB)
File:Mic 98583.png|link=MIC 98583|[[File:Nuvola OK.png|16px]] [[MIC 98583]] (1xtemp, 1xhum, USB)
File:Uni-t ut325 front.png|link=UNI-T UT325|[[File:Nuvola OK.png|16px]] [[UNI-T UT325]] (2xtemp, USB)
File:Voltcraft k204.png|link=Voltcraft K204|[[File:Nuvola OK.png|16px]] [[Voltcraft K204]] (4xtemp, RS232)
File:rs55ii.png|link=APPA 55II|[[File:Nuvola Red.png|16px]] [[APPA 55II]] (2xtemp, RS232)
File:Elitech rc3.png|link=Elitech RC-3|[[File:Nuvola Red.png|16px]] [[Elitech RC-3]] (1xtemp, RS232)
File:Pce_pce-222_front.png|link=PCE PCE-222|[[File:Nuvola Red.png|16px]] [[PCE PCE-222]] (1xtemp, RS232)
File:Rding temper front.png|link=RDing TEMPer|[[File:Nuvola Red.png|16px]] [[RDing TEMPer]] (1xtemp, USB)
File:Rding temper gold device front.png|link=RDing TEMPer Gold|[[File:Nuvola Red.png|16px]] [[RDing TEMPer Gold]] (1xtemp, USB)
File:Rding temper1 device front.png|link=RDing TEMPer1|[[File:Nuvola Red.png|16px]] [[RDing TEMPer1]] (1xtemp, USB)
File:Pcsensor_temper1k2.png|link=RDing TEMPer1K2|[[File:Nuvola Red.png|16px]] [[RDing TEMPer1K2]] (1xtemp, USB)
File:Voltcraft dl-120th.png|link=Voltcraft DL-120TH|[[File:Nuvola Red.png|16px]] [[Voltcraft DL-120TH]] (1xtemp, USB)
File:Voltcraft dl-140th.png|link=Voltcraft DL-140TH|[[File:Nuvola Red.png|16px]] [[Voltcraft DL-140TH]] (1xtemp, USB)
</gallery>

== Hygrometers ==

<gallery widths="100px" heights="100px">
File:EL-USB-2.png|link=Lascar Electronics EL-USB-2|[[File:Nuvola OK.png|16px]] [[Lascar Electronics EL-USB-2]] (temp/humidity, USB)
File:Mic 98583.png|link=MIC 98583|[[File:Nuvola OK.png|16px]] [[MIC 98583]] (temp/humidity, USB)
File:Pce_pce-222_front.png|link=PCE PCE-222|[[File:Nuvola Red.png|16px]] [[PCE PCE-222]] (also: light-/soundlevelmeter; RS232)
File:Silabs si7005usb dgl eb top.jpg|link=SiLabs Si7005USB-Dongle|[[File:Nuvola Red.png|16px]] [[SiLabs Si7005USB-Dongle]] (USB)
</gallery>

== Anemometers ==

<gallery widths="100px" heights="100px">
File:Mastech ms6252b.png|link=MASTECH MS6252B|[[File:Nuvola Red.png|16px]] [[MASTECH MS6252B]] (USB)
</gallery>

== Light meters ==

<gallery widths="100px" heights="100px">
File:Lutron YK-2005LX.png|link=Lutron YK-2005LX|[[File:Nuvola Red.png|16px]] [[Lutron YK-2005LX]] (RS232)
File:Pce_pce-222_front.png|link=PCE PCE-222|[[File:Nuvola Red.png|16px]] [[PCE PCE-222]] (RS232)
</gallery>

== Energy meters ==

<gallery widths="100px" heights="100px">
File:Actaris_a14c5_teleinfo.png|link=EDF Teleinfo|[[File:Nuvola OK.png|16px]] [[EDF Teleinfo]] (USB)
</gallery>

== DAQs ==

<gallery widths="100px" heights="100px">
File:Ni usb 6008.png|link=NI USB-6008|[[File:Nuvola Red.png|16px]] [[NI USB-6008]] (8/2 analog inputs/outputs, 12 digital I/Os)
</gallery>

== Dataloggers ==

<gallery widths="100px" heights="100px">
File:EL-USB-CO.png|link=Lascar Electronics EL-USB-CO|[[File:Nuvola OK.png|16px]] [[Lascar Electronics EL-USB-CO]] (carbon monoxide (CO) logger, USB)
File:Gsg_indoor_air_monitor.png|link=GSG Indoor Air Monitor|[[File:Nuvola Red.png|16px]] [[GSG Indoor Air Monitor]] (air quality monitor, USB)
File:Maul_studio_i.png|link=MAUL studio i|[[File:Nuvola Red.png|16px]] [[MAUL studio i]] (weighing scale, RS232)
File:Voltcraft co-20.png|link=Voltcraft CO-20|[[File:Nuvola Red.png|16px]] [[Voltcraft CO-20]] (air quality monitor, USB)
</gallery>

== Function generators ==

<gallery widths="100px" heights="100px">
File:Hantek DDS-3X25 top.png|link=Hantek DDS-3X25|[[File:Nuvola Red.png|16px]] [[Hantek DDS-3X25]] (25MHz, PC-based, USB)
File:Siglent sdg1010 device front 8116.png|link=Siglent SDG1010|[[File:Nuvola Red.png|16px]] [[Siglent SDG1010]] (10MHz, USB)
</gallery>

== RF receivers ==

<gallery widths="100px" heights="100px">
File:Sigrok_logo_no_text_transparent_512.png|link=Per Vices Noctar|[[File:Nuvola Red.png|16px]] [[Per Vices Noctar]] (100kHz-4GHz, IQ modulator/demodulator, PCIe)
</gallery>

== Spectrum analyzers ==

TODO.

== Power supplies ==

<gallery widths="100px" heights="100px">
File:Manson hcs3202.png|link=Manson HCS-3202|[[File:Nuvola Red.png|16px]] [[Manson HCS-3202]] (1ch, 1-36V/0-10A, USB)
</gallery>

== GPIB interfaces ==

<gallery widths="100px" heights="100px">
File:Beiming_s82357.png|link=Beiming S82357|[[File:Nuvola Red.png|16px]] [[Beiming S82357]] (hardware-based, USB)
File:ICS 488-USB.png|link=ICS 488-USB|[[File:Nuvola Red.png|16px]] [[ICS 488-USB]] (hardware-based, USB)
File:GPIB-USB 82357B clone.png|link=GPIB-USB 82357B clone|[[File:Nuvola Red.png|16px]] [[GPIB-USB 82357B clone]] (hardware-based, USB)
File:NI GPIB-ENET.png|link=National Instruments GPIB-ENET|[[File:Nuvola Red.png|16px]] [[National Instruments GPIB-ENET]] (hardware-based, Ethernet)
File:NI GPIB-USB-HS.png|link=National Instruments GPIB-USB-HS|[[File:Nuvola Red.png|16px]] [[National Instruments GPIB-USB-HS]] (hardware-based, USB)
File:Prologix-usb.png|link=Prologix GPIB-USB|[[File:Nuvola Red.png|16px]] [[Prologix GPIB-USB]] (firmware-based, USB)
</gallery>

== Potential other candidates ==

If you own any other logic analyzers, oscilloscopes, multimeters, dataloggers, ... and want to add support for them in sigrok (or donate/lend devices to developers), please let us know. We're always happy to add more hardware support! Join the [https://lists.sourceforge.net/lists/listinfo/sigrok-devel mailing list] or ask on [irc://chat.freenode.net/sigrok IRC #sigrok] if you want to help out.

__FORCETOC__

UNI-T UT61B

2014-01-01T18:27:57Z

Tsaitgaist: created

{{Infobox multimeter
| image = [[File:Uni-t_ut61b_device.png|180px]]
| name = UNI-T UT61B
| status = supported
| source_code_dir = uni-t-dmm
| counts = 4000
| categories = CAT II (600V) / CAT III (300V)
| connectivity = [[Device_cables#UNI-T_UT-D02|RS232]] / [[Device_cables#UNI-T_UT-D04|USB]]
| measurements = voltage, current, resistance, capacitance, frequency, duty cycle, diode, continuity, temperature
| features = autorange, data hold, min/max, rel, bargraph, backlight
| website = [http://www.uni-trend.com/UT61B.html uni-trend.com]
}}

The '''UNI-T UT61B''' is a 4000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity.

== Hardware ==

'''Multimeter''':
* '''Multimeter IC''': [[Multimeter_ICs#Fortune_Semiconductor_FS9922-DMM3|Fortune Semiconductor FS9922-DMM3]] ([http://www.ic-fortune.com/upload/Download/FS9922-DMM3-DS-10_EN.pdf datasheet])
* '''Crystal''': 4MHz (markings: "3.999")
* '''Fuses''': 0.5A/600V and 10A/600V (HRV fuses)

'''RS232 cable''':

See [[Device cables#UNI-T_UT-D02]].

'''USB cable''':

See [[Device cables#UNI-T_UT-D04]].

== Photos ==

'''Multimeter''':

<gallery>
File:Uni-t_ut61b_device.png|Device, front
File:Uni-t_ut61b_back.jpg|Device, back
File:Uni-t_ut61b_battery.jpg|Battery
File:Uni-t ut61b_inside-back.jpg|Device open back
File:Uni-t_ut61b_inside-front.jpg|Device open front
File:Uni-t_ut61b_pcb-front.jpg|PCB, front
File:Uni-t_ut61b_pcb-back.jpg|PCB, back
</gallery>

'''RS232 cable''':

See [[Device cables#UNI-T_UT-D02]].

'''USB cable''':

See [[Device cables#UNI-T_UT-D04]].

== Protocol ==

See [[Multimeter_ICs#Fortune_Semiconductor_FS9922-DMM3]] for the DMM IC protocol. Depending on the cable, additional transport-specific decoding is needed, though.

== Resources ==

* [http://www.uni-trend.com/manual2/UT61English.pdf Manual]
* [http://www.uni-trend.com/Web%20site/DMM%20Software/UT61B%20setup.exe Vendor software]
* [https://perhof.wordpress.com/category/computing/linux/ perhof: Uni-T UT61D for Linux] (also: [http://dl.dropbox.com/u/20603229/published/ut61d.zip ut61d.zip])

[[Category:Device]]
[[Category:Multimeter]]
[[Category:Supported]]

File:Uni-t ut61b battery.jpg

2014-01-01T18:24:05Z

Tsaitgaist: UNI-T UT61B DMM back battery view

== Summary ==
UNI-T UT61B DMM

back battery view
== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut61b back.jpg

2014-01-01T18:19:05Z

Tsaitgaist: add license

UNI-T UT61B DMM

back view

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut61b inside-back.jpg

2014-01-01T18:18:53Z

Tsaitgaist: add license

UNI-T UT61B DMM

back inside view

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut61b inside-front.jpg

2014-01-01T18:18:43Z

Tsaitgaist: add licence

UNI-T UT61B DMM

front inside view

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut61b pcb-front.jpg

2014-01-01T18:18:19Z

Tsaitgaist: UNI-T UT61B DMM front PCB view

== Summary ==
UNI-T UT61B DMM

front PCB view
== Licensing ==
{{CC-BY-SA-3.0}}

File:UT81-USB cable opened.jpg

2014-01-01T18:17:48Z

Tsaitgaist: add license

USB-HID data cable used for a UNI-T UT61B

view of the internal PCB

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut61b pcb-back.jpg

2014-01-01T18:15:58Z

Tsaitgaist: /* Summary */ typo

== Summary ==
UNI-T UT61B DMM

back PCB view

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut61b pcb-back.jpg

2014-01-01T18:15:41Z

Tsaitgaist: UNI-T UT61B DMM bacl PCB view

== Summary ==
UNI-T UT61B DMM

bacl PCB view
== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut61b inside-front.jpg

2014-01-01T18:14:06Z

Tsaitgaist: UNI-T UT61B DMM front inside view

UNI-T UT61B DMM

front inside view

File:Uni-t ut61b inside-back.jpg

2014-01-01T18:13:09Z

Tsaitgaist: UNI-T UT61B DMM back inside view

UNI-T UT61B DMM

back inside view

File:Uni-t ut61b back.jpg

2014-01-01T18:12:12Z

Tsaitgaist: UNI-T UT61B DMM back view

UNI-T UT61B DMM

back view

File:Uni-t ut61b device.png

2014-01-01T18:02:55Z

Tsaitgaist: UNI-T UT61B DMM front view

== Summary ==
UNI-T UT61B DMM

front view
== Licensing ==
{{CC-BY-SA-3.0}}

Device cables/Info

2014-01-01T17:18:25Z

Tsaitgaist: /* UNI-T UT-D04 */ fixed formatting

= Multimeters =

== UNI-T UT-D04 ==

'''How to get a proper lsusb:'''

As [http://erste.de/UT61/index.html documented by Ralf Burger] the [[Device cables#UNI-T_UT-D04|UT-D04]] USBHID-to-serial cable (at least the one with WCH CH9325 chip) that comes with the UT61D multimeter has some issues on Linux. Apparently you need to [http://www.lesswatts.org/projects/devices-power-management/usb.php put it into (auto)suspend first], before you can properly use it.

Here's a script (written by Ralf Burger) which you can run before using the chip and/or doing an lsusb:


$ '''cat suspend.HE2325U.sh'''
#!/bin/bash
for dat in /sys/bus/usb/devices/*; do
if test -e $dat/manufacturer; then
grep "WCH.CN" $dat/manufacturer > /dev/null && echo auto > ${dat}/power/level && echo 0 > ${dat}/power/autosuspend
fi
done


'''lsusb:'''

This is the lsusb ouput on Linux:


$ '''lsusb -vvv'''
Bus 003 Device 023: ID '''1a86:e008 QinHeng Electronics HID-based serial adapater'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x1a86 '''QinHeng Electronics'''
idProduct 0xe008 '''HID-based serial adapater'''
bcdDevice 11.00
iManufacturer 1 '''WCH.CN �'''
iProduct 2 '''USB to Serial'''
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 41
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 '''Human Interface Device'''
bInterfaceSubClass 0 '''No Subclass'''
bInterfaceProtocol 0 '''None'''
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 37
Report Descriptor: (length is 37)
Item(Global): Usage Page, data= [ 0xa0 0xff ] 65440
(null)
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Collection, data= [ 0x01 ] 1
'''Application'''
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Global): Logical Minimum, data= [ 0x00 ] 0
Item(Global): Logical Maximum, data= [ 0xff 0x00 ] 255
Item(Global): Report Size, data= [ 0x08 ] '''8'''
Item(Global): Report Count, data= [ 0x08 ] '''8'''
Item(Main ): '''Input''', data= [ 0x02 ] 2
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Non_Volatile Bitfield
Item(Local ): Usage, data= [ 0x02 ] 2
(null)
Item(Global): Report Size, data= [ 0x08 ] '''8'''
Item(Global): Report Count, data= [ 0x08 ] '''8'''
Item(Main ): '''Output''', data= [ 0x02 ] 2
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Non_Volatile Bitfield
Item(Local ): Usage, data= [ 0x03 ] 3
(null)
Item(Global): Report Size, data= [ 0x08 ] '''8'''
Item(Global): Report Count, data= [ 0x05 ] '''5'''
Item(Main ): '''Feature''', data= [ 0x02 ] 2
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Non_Volatile Bitfield
Item(Main ): End Collection, data=none
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 '''EP 2 IN'''
bmAttributes 3
Transfer Type '''Interrupt'''
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 '''EP 2 OUT'''
bmAttributes 3
Transfer Type '''Interrupt'''
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Device Status: 0x0000
(Bus Powered)


'''lsusb of slightly different cables:'''

There is another cable version apparently which also has the USB VID/PID 1a86:e008 ("QinHeng Electronics HID-based serial adapater"), but with slightly different lsusb output. Both cables work fine with the same code, it's unclear what the differences are (or whether they relate to the chip/hardware or to some kind of firmware or ROM).


- bcdDevice 12.00
- iManufacturer 1 WCH.CN ^R
+ bcdDevice 11.00
+ iManufacturer 1 WCH.CN ^Q


here the USB VID/PID are the same, but some details are different, and it advertises itself as self-powered, which it isn't.


Bus 001 Device 040: ID 1a86:e008 QinHeng Electronics HID-based serial adapater
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x1a86 QinHeng Electronics
idProduct 0xe008 HID-based serial adapater
bcdDevice 12.00
iManufacturer 1 (error)
iProduct 2 (error)
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 41
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 (error)
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 37
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Device Status: 0x0001
Self Powered


'''usbhid-dump:'''


$ '''usbhid-dump'''
003:009:000:DESCRIPTOR 1347198370.436452
06 A0 FF 09 01 A1 01 09 01 15 00 26 FF 00 75 08
95 08 81 02 09 02 75 08 95 08 91 02 09 03 75 08
95 05 B1 02 C0


'''Simple USB Logger (Windows):'''

This is a screenshot of the decoded HID data, using the [http://www.incentivespro.com/downloads.html Simple USB Logger] Windows tool.

[[File:Uni t-ut-d04 hid.png]]

== V&A VA4000 ==

=== Old version: Sunplus SPCP825 ===

'''lsusb:'''


$ '''lsusb -vvv'''
Bus 005 Device 069: ID '''04fc:0201 Sunplus Technology Co., Ltd'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x04fc '''Sunplus Technology Co., Ltd'''
idProduct 0x0201
bcdDevice 1.00
iManufacturer 0
iProduct 2 '''RS232C to USB Adapter'''
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 0 (Defined at Interface level)
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)


=== New version: Prolific PL2303HX ===

'''lsusb:'''


$ '''lsusb -vvv'''
Bus 005 Device 098: ID '''067b:2303 Prolific Technology, Inc. PL2303 Serial Port'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x067b '''Prolific Technology, Inc.'''
idProduct 0x2303 '''PL2303 Serial Port'''
bcdDevice 3.00
iManufacturer 1 '''Prolific Technology Inc.'''
iProduct 2 '''USB-Serial Controller'''
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x000a 1x 10 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)


__FORCETOC__

Device cables/Info

2014-01-01T17:16:07Z

Tsaitgaist: /* UNI-T UT-D04 */ add different cable

Device cables/Info

2014-01-01T17:12:57Z

Tsaitgaist: /* UNI-T UT-D04 */ add differents lsusb

= Multimeters =

== UNI-T UT-D04 ==

'''How to get a proper lsusb:'''

As [http://erste.de/UT61/index.html documented by Ralf Burger] the [[Device cables#UNI-T_UT-D04|UT-D04]] USBHID-to-serial cable (at least the one with WCH CH9325 chip) that comes with the UT61D multimeter has some issues on Linux. Apparently you need to [http://www.lesswatts.org/projects/devices-power-management/usb.php put it into (auto)suspend first], before you can properly use it.

Here's a script (written by Ralf Burger) which you can run before using the chip and/or doing an lsusb:


$ '''cat suspend.HE2325U.sh'''
#!/bin/bash
for dat in /sys/bus/usb/devices/*; do
if test -e $dat/manufacturer; then
grep "WCH.CN" $dat/manufacturer > /dev/null && echo auto > ${dat}/power/level && echo 0 > ${dat}/power/autosuspend
fi
done


'''lsusb:'''

This is the lsusb ouput on Linux:


$ '''lsusb -vvv'''
Bus 003 Device 023: ID '''1a86:e008 QinHeng Electronics HID-based serial adapater'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x1a86 '''QinHeng Electronics'''
idProduct 0xe008 '''HID-based serial adapater'''
bcdDevice 11.00
iManufacturer 1 '''WCH.CN �'''
iProduct 2 '''USB to Serial'''
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 41
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 '''Human Interface Device'''
bInterfaceSubClass 0 '''No Subclass'''
bInterfaceProtocol 0 '''None'''
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 37
Report Descriptor: (length is 37)
Item(Global): Usage Page, data= [ 0xa0 0xff ] 65440
(null)
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Collection, data= [ 0x01 ] 1
'''Application'''
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Global): Logical Minimum, data= [ 0x00 ] 0
Item(Global): Logical Maximum, data= [ 0xff 0x00 ] 255
Item(Global): Report Size, data= [ 0x08 ] '''8'''
Item(Global): Report Count, data= [ 0x08 ] '''8'''
Item(Main ): '''Input''', data= [ 0x02 ] 2
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Non_Volatile Bitfield
Item(Local ): Usage, data= [ 0x02 ] 2
(null)
Item(Global): Report Size, data= [ 0x08 ] '''8'''
Item(Global): Report Count, data= [ 0x08 ] '''8'''
Item(Main ): '''Output''', data= [ 0x02 ] 2
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Non_Volatile Bitfield
Item(Local ): Usage, data= [ 0x03 ] 3
(null)
Item(Global): Report Size, data= [ 0x08 ] '''8'''
Item(Global): Report Count, data= [ 0x05 ] '''5'''
Item(Main ): '''Feature''', data= [ 0x02 ] 2
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Non_Volatile Bitfield
Item(Main ): End Collection, data=none
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 '''EP 2 IN'''
bmAttributes 3
Transfer Type '''Interrupt'''
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 '''EP 2 OUT'''
bmAttributes 3
Transfer Type '''Interrupt'''
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Device Status: 0x0000
(Bus Powered)


'''lsusb of slightly different cable:'''

There is another cable version apparently which also has the USB VID/PID 1a86:e008 ("QinHeng Electronics HID-based serial adapater"), but with slightly different lsusb output. Both cables work fine with the same code, it's unclear what the differences are (or whether they relate to the chip/hardware or to some kind of firmware or ROM).


- bcdDevice 12.00
- iManufacturer 1 WCH.CN ^R
+ bcdDevice 11.00
+ iManufacturer 1 WCH.CN ^Q


'''usbhid-dump:'''


$ '''usbhid-dump'''
003:009:000:DESCRIPTOR 1347198370.436452
06 A0 FF 09 01 A1 01 09 01 15 00 26 FF 00 75 08
95 08 81 02 09 02 75 08 95 08 91 02 09 03 75 08
95 05 B1 02 C0


'''Simple USB Logger (Windows):'''

This is a screenshot of the decoded HID data, using the [http://www.incentivespro.com/downloads.html Simple USB Logger] Windows tool.

[[File:Uni t-ut-d04 hid.png]]

== V&A VA4000 ==

=== Old version: Sunplus SPCP825 ===

'''lsusb:'''


$ '''lsusb -vvv'''
Bus 005 Device 069: ID '''04fc:0201 Sunplus Technology Co., Ltd'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x04fc '''Sunplus Technology Co., Ltd'''
idProduct 0x0201
bcdDevice 1.00
iManufacturer 0
iProduct 2 '''RS232C to USB Adapter'''
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 0 (Defined at Interface level)
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)


=== New version: Prolific PL2303HX ===

'''lsusb:'''


$ '''lsusb -vvv'''
Bus 005 Device 098: ID '''067b:2303 Prolific Technology, Inc. PL2303 Serial Port'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x067b '''Prolific Technology, Inc.'''
idProduct 0x2303 '''PL2303 Serial Port'''
bcdDevice 3.00
iManufacturer 1 '''Prolific Technology Inc.'''
iProduct 2 '''USB-Serial Controller'''
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x000a 1x 10 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)


__FORCETOC__

Device cables

2014-01-01T17:05:29Z

Tsaitgaist: /* UNI-T UT-D04 */ other cable added

This page contains information and teardown photos of various multimeter/datalogger/etc. PC connectivity cables and adapters.

= Multimeters =

== Agilent U1173A ==

The [http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&ckey=792204&nid=-536906710.536910943.00&id=792204&pselect=SR.GENERAL Agilent U1173A] is an IR-USB cable.

'''Hardware''':
* Prolific PL2303HX (max. baudrate 19200, according to the Agilent website)

''' Works with''':
* Agilent U1230/40/50/70 series
* Note: For the U1240 series, the additional [http://www.home.agilent.com/agilent/redirector.jspx?action=ref&lc=ger&cc=DE&nfr=-536906710.536910943&ckey=2101709&cname=PRODUCT U1179A] IR bracket is required.[http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&nid=-536906710.536910943&pageMode=OV 1]

''' Where to buy''':
* [http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&ckey=792204&nid=-536906710.536910943.00&id=792204&pselect=SR.GENERAL Agilent] ($31)
* [http://www.newark.com/agilent-technologies/u1173a/ir-to-usb-connectivity-cable-assembly/dp/04M7391 Newark] ($31)
* [http://www.datatec.de/U1173A-Agilent-Adapterkabel.htm Datatec] (€23)

<gallery>
File:Agilent U1173A.jpg|Device, front
File:Agilent U1173A PCB.jpg|PCB, front
File:Agilent U1173A PCB back.jpg|PCB, back
</gallery>

== Agilent U1177A ==

The [http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&ckey=2090364&nid=-536902461.1006710.00&id=2090364&pselect=SR.GENERAL Agilent U1177A] is an IR-Bluetooth interface module.

Notes: 9600 baud, 8n1 settings on the PC. The protocol (AT commands) allows changing the baud rate to 19200, among other things.[http://www.home.agilent.com/agilent/redirector.jspx?action=ref&cname=AGILENT_EDITORIAL&ckey=2150265&lc=ger&cc=DE&nfr=-536902461.1006710.00 1] Default Bluetooth PIN: 1234. For the U1240 series, the additional [http://www.home.agilent.com/agilent/redirector.jspx?action=ref&lc=ger&cc=DE&nfr=-536906710.536910943&ckey=2101709&cname=PRODUCT U1179A] IR bracket is required.[http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&nid=-536906710.536910943&pageMode=OV 2]

'''Hardware''':
* CSR BC417...
* Macronix MX...
* PCB markings: U1177-26500, REV004, MSD-02

''' Works with''':
* Agilent U1230/40/50/70 series

''' Where to buy''': 
It is often given away free as a promotion with one of the Agilent U12xxA meters, but can also be purchased separately:
* [http://www.home.agilent.com/agilent/product.jspx?cc=DE&lc=ger&ckey=2090364&nid=-536902461.1006710.00&id=2090364&pselect=SR.GENERAL Agilent] ($49)
* [http://www.datatec.de/Agilent-1177A-Bluetooth.htm Datatec] (€36)

<gallery>
File:Agilent U1177A.jpg|Device, front
File:Agilent U1177A back.jpg|Device, back
File:Agilent U1177A battery.jpg|Battery compartment
File:Agilent U1177A PCB.jpg|PCB, front
File:Agilent U1177A PCB back.jpg|PCB, back
</gallery>

== Amprobe 38SW-A ==

The [http://www.amprobe.eu/en_GB/showproduct/234/38SW-A/ Amprobe 38SW-A] is an RS232 PC interface cable for the [http://www.amprobe.eu/en_GB/showproduct/134/38XR-A/ Amprobe 38XR-A] multimeter. The "38SW-A" name is also used to refer to the respective PC software for use with the serial cable.

'''Hardware''':
* TODO.

''' Works with''':
* [http://www.amprobe.eu/en_GB/showproduct/134/38XR-A/ Amprobe 38XR-A]

''' Where to buy''':
* [http://www.digikey.com/product-detail/en/38SW-A/38SW-A-ND/1540519 Digikey], [http://www.tme.eu/de/details/38sw-a/messgerate-software/amprobe/38sw/ TME.eu], [http://de.rs-online.com/mobile/p/digital-multimeter/0411722/ RS Components], [http://www.mercateo.com/p/115-911905/38SW_A_Interfacekabel_und_Software.html Mercateo], [http://www.testersandtools.com/Amprobe-38SW-A-RS232-Software-Cable.php testersandtools.com], [http://www.newark.com/amprobe-instruments/38sw-a/rs-232-cable-software-38xr-a/dp/29M6230 Newark], [https://www.distrelec.de/interfacekabel-und-software/amprobe/38sw-a/911905/de Distrelec], and various others.
* The usual price is around €20-€35, depending on vendor and location.

<gallery>
File:Amprobe 38sw a cable package top.jpg|Package, top
File:Amprobe 38sw a cable package bottom.jpg|Package, bottom
File:Amprobe 38sw a cable top.jpg|Cable, top
File:Amprobe 38sw a cable bottom.jpg|Cable, bottom
File:Amprobe 38sw a cable cdrom top.jpg|CD-ROM, top
File:Amprobe 38sw a cable cdrom bottom.jpg|CD-ROM, bottom
File:Amprobe 38sw a cable cdrom contents.jpg|CD-ROM, contents
File:Amprobe 38sw a cable open.jpg|Cable, opened
File:Amprobe 38sw a cable housing1.jpg|Housing 1
File:Amprobe 38sw a cable housing2.jpg|Housing 2
File:Amprobe 38sw a cable pcb top.jpg|PCB, top
File:Amprobe 38sw a cable pcb bottom.jpg|PCB, bottom
File:Amprobe 38sw a cable pcb pinout.jpg|PCB, pinout
</gallery>

== APPA / ISO-TECH IC50 ==

The IC50 is a USB PC interface cable for some APPA and ISO-TECH multimeters and thermometers.

''' Works with''':
* [http://www.appatech.com/appa_product_home.php?pdid=2005102401295373290&kindid=2005081003113623241 APPA 70] series multimeters (and ISO-TECH IDM 70 series clone)
* [http://www.appatech.com/appa_product_home.php?pdid=20051220112048498347&kindid=20050810031145946832 APPA 50] series thermometer (and RS 50 series clone)

''' Where to buy''':
* [http://uk.rs-online.com/web/p/multimeter-accessories/7048135/ RS 704-8135]
* The price is around 40 €

== APPA / ISO-TECH IC70 ==

The IC70 is an RS232 PC interface cable for some APPA and ISO-TECH multimeters and thermometers.

''' Works with''':
* [http://www.appatech.com/appa_product_home.php?pdid=2005102401295373290&kindid=2005081003113623241 APPA 70] series multimeters (and ISO-TECH IDM 70 series clone)
* [http://www.appatech.com/appa_product_home.php?pdid=20051220112048498347&kindid=20050810031145946832 APPA 50] series thermometer (and RS 50 series clone)

''' Where to buy''':
* [http://uk.rs-online.com/web/p/digital-multimeters/4609881/ RS 460-9881]
* The price is around 20 €

<gallery>
File:Ic70 optical serial cable.jpeg|Cable
</gallery>

== Brymen BC-85X(-1) ==

Not compatible with BC-85Xa.

TODO.

'''Hardware''':
* TODO.

''' Works with''':
* Brymen BM857/BM859 (non-a versions)

''' Where to buy''':
* Available from Greenlee as DMSC-9 (not DMSC-9U).
* [http://www.tme.eu/en/details/kitrs232c/meters-software/ TME] (€26.82)

=== Brymen BR85X interface kit ===

<gallery>
File:Brymen_br85x_cable.jpg|Kit contents (software disc not shown)
File:Brymen_br85x_rs232_conn.jpg|BC-85X-1 DB9 connector
File:Brymen_br85x_dmm_end.jpg|BC-85Xa DMM connector
</gallery>

== Brymen BC-85Xa ==

Not compatible with BC-85X.

TODO.

'''Hardware''':
* TODO.

''' Works with''':
* Brymen BM857a/BM859a
* Extech MM570A/MM560A/MP530A/MP510A

''' Where to buy''':
* Available from Extech in a kit with USB-to-serial converter and software disc, under the name SW-810a.
* [http://de.mouser.com/Search/ProductDetail.aspx?qs=zS8Kl81wrHovBIt5EskF9A== Mouser] (€65.99)
* [http://www.tme.eu/de/details/sw810a/umgebungsmesser-sonstige/extech/ TME] (€60.60)

=== Extech SW-810a kit ===

This is a kit sold by Extech, containing the BC-85Xa RS232 cable, the BUA2303 USB-to-serial adapter, a USB cable, and a software disc.

<gallery>
File:Extech_sw810a_kit.jpg|Kit contents (software disc not shown)
File:Extech_sw810a_ir_db9.jpg|BC-85Xa DB9 connector
File:Extech_sw810a_id_dmm_hookup.jpg|BC-85Xa DMM connector
File:Extech_sw810a_usb2serial.jpg|BUA2303 USB-to-serial converter
File:Extech_sw810a_usb2serial_back.jpg|BUA2303 USB-to-serial converter, back
File:Extech_sw810a_usb2serial_bottom.jpg|BUA2303 USB-to-serial converter, bottom
File:Extech_sw810a_IR_opened.jpg|IR side, opened
File:Extech_sw810a_ir_casing.jpg|IR side casing
File:Extech_sw810a_ir_pcb_top.jpg|IR side PCB, top
File:Extech_sw810a_ir_pcb_bottom.jpg|IR side PCB, botoom
File:Extech_sw810a_usb2serial_pcb_top.jpg|BUA2303 PCB, top
File:Extech_sw810a_usb2serial_pcb_bottom.jpg|BUA2303 PCB, bottom
</gallery>

== Brymen BU-86X ==

TODO.

'''Hardware''':
* TODO.

''' Works with''':
* Brymen BM867/BM869

''' Where to buy''':
* TODO.

== Digitek DT4000ZC cable ==

The [[Digitek DT4000ZC]] (and the rebadged [[TekPower TP4000ZC]]) ship with this RS232 to 3.5mm stereo plug cable. The ring on the plug is left unconnected.

The cable works on the assumption that TX (pin 3) and DTR (pin 4) are at a fixed voltage and will not be toggled. TX should be below -3 V, and the resistor acts as a pull-down. DTR should be abouve 3V. The photodiode/phototransistor in the DMM will pull the RX pin above 3V when the IR diode is on.

'''Hardware''':
* SMD resistor between TX and RX pins.

''' Works with''':
* [[Digitek DT4000ZC]], [[TekPower TP4000ZC]]

''' Where to buy''':
* The cable ships with the multimeter. It's unclear whether it can be bought standalone (without DMM).

[[Digitek DT4000ZC]] photos:

<gallery>
File:Digitek dt4000zc cable front.jpg|Device, front
File:Digitek dt4000zc cable back.jpg|Device, back
File:Digitek dt4000zc cable open.jpg|Device, open
File:Digitek dt4000zc cable open2.jpg|Device, open 2
File:Digitek dt4000zc cable resistor.jpg|Resistor
</gallery>

[[TekPower TP4000ZC]] photos:

<gallery>
File:Tp4000zc_232_cable.jpg|Supplied RS-232 cable
File:Tp4000zc_232_cable_open.jpg|RS-232 cable, disassembled
File:Tp4000zc_232_cable_detail.jpg|RS-232 cable, detail
</gallery>

== Fluke IR189USB ==

The [http://www.flukeonlinestore.com/2428108.html Fluke IR189USB] is a USB interface cable for Fluke-18x and 28x series DMMs. It is a basic USB-serial cable, based on the [http://www.ftdichip.com/Products/ICs/FT232R.htm FTDI FT232RL] chip.

<gallery>
File:Fluke IR189USB.jpg
File:Fluke IR189USB bottom.jpg
File:Fluke IR189USB PCB top.jpg
File:Fluke IR189USB PCB bottom.jpg
</gallery>

== Fluke OC4USB ==

The [http://www.flukeonlinestore.com/2166266.html Fluke OC4USB] is a USB interface cable for the Fluke 120 series, 190 series scope meter, and the 430 series power quality analyzer.

Resources:
* [http://omapalvelin.homedns.org/fluke/ DIY optical link cable for the Fluke Scopemeter 190 series]

== Fluke PM9080 ==

The [http://www.flukeonlinestore.com/1641983.html Fluke PM9080] is an RS232 interface cable for "digital hard-copy output to serial printer or remote control via a PC".

The max. supported baud rate is 57600.

'''Hardware''':
No active components are on the PCB.

Pinout:
* black: pin 2 (RX)
* brown: pin 3 (TX)
* red: pin 7, 8 (RTS, CTS)
* orange: pin 1, 4, 6 (DCD, DTR, DSR)
* yellow: pin 5 (GND)

''' Works with''':
* Fluke scope meter test tools, power harmonics analyzers, graphical multimeters and multifunction counters.

'''Where to buy''':
* [http://www.flukeonlinestore.com/1641983.html flukeonlinestore.com] ($185.95)
* [http://www.fluke.eu/comx/show_product.aspx?locale=dede&pid=31870 fluke.eu] (€240.-)
* [http://de.farnell.com/fluke/pm9080/pm9080-rs-232-adapter-kabel-optisch/dp/252384 Farnell] (€240.-)
* [http://www.instrumentation2000.com/flukepm9080opticallyisolatedrs-232adaptercable.aspx instrumentation2000.com] ($187.95)
* [http://de.rs-online.com/web/p/interface-adapter/4256752/ RS-Online] (€245.-)
* [http://www.amazon.com/Fluke-PM9080-101-Optically-Isolated/dp/B000LEDHHS Amazon] ($168.23)

'''Resources''':
* [http://omapalvelin.homedns.org/fluke/ DIY optical link cable for the Fluke Scopemeter 190 series]
* [http://www.scopemeter.com/accessories/PM9080.htm PM9080 Optically-isolated RS-232C Interface Adapter] (comparison of the different cable revisions)

<gallery>
File:Fluke PM9080 top.jpg
File:Fluke PM9080 bottom.jpg
File:Fluke PM9080 LEDs.jpg
File:Fluke PM9080 PCB top.jpg
File:Fluke PM9080 PCB bottom.jpg
</gallery>

== Gossen Metrawatt ==
See [[Gossen Metrawatt#Communication Hardware|Gossen Metrawatt]] page.

== GreenLee DMSC-9U ==

TODO.

'''Hardware''':
* TODO.

''' Works with''':
* GreenLee DM-800 series, DML-430A

''' Where to buy''':
* TODO.

== Metex 5-pin RS232 cable ==

This type of 5-pin RS232 cable is used in various Metex (and rebadged) multimeters.

The cable exists in two flavours, an older version with equal pin distance (can be inserted the wrong way) and a newer version with a gap between pins 3 and 4 (fits only one way).

=== Version 1 ===
'''Hardware''':
* No active components.
* 25-pin RS232 connector

''' Works with''':
* [[Voltcraft M-3650CR]], many others.

''' Where to buy''':
* The cable ships with the respective multimeter. It's unclear whether it can be bought standalone (without DMM).

=== Version 2 ===
'''Hardware''':
* No active components.
* 9-pin RS232 connector

''' Works with''':
* [[MASTECH MAS345]], [[Voltcraft M-3650CR]] (plug with equal pin distances!), [[RadioShack 22-168]], [[Voltcraft M-3650D]], many others.

''' Where to buy''':
* The cable ships with the respective multimeter. It's unclear whether it can be bought standalone (without DMM).

[[MASTECH MAS345]]:
<gallery>
File:Mastech mas345 rs232 cable.jpg|Cable
File:Mastech mas345 rs232 cable connected.jpg|Cable, connected
</gallery>

[[RadioShack 22-168]]:
<gallery>
File:Rs_22_168_cable.jpg|RS-232 cable
File:Rs_22_168_cable_dmm_end.jpg|DMM connector
File:Rs_22_168_cable_dmm_end_exposed.jpg|DMM connector, protective sheath removed
File:Rs_22_168_cable_internals.jpg|DB9 connector, opened
File:Rs_22_168_cable_connection.jpg|DB9 connections
</gallery>

'''DIY:'''
<gallery>
File:MetexDIY.JPG|DIY adapter
File:MetexAnschluss.JPG|Pin numbers (Metex DMM)
</gallery>

=== Cable pinout ===
{| border="0" style="font-size: smaller;" class="alternategrey sigroktable"
!Metex-connector pin (male)
!RS-232 25-pin female
!RS-232 DE9-female pin
!Signal (computer side)
!Remarks
|-
| 1 || 7 || 5 || GND ||
|-
| 2 || 2 || 3 || TX ||
|-
| 3 || 4 || 7 || RTS || Used to power receiver in multimeter, must be OFF.
|-
| 4 ||20 || 4 || DTR || Used to power receiver in multimeter, must be ON.
|-
| 5 || 3 || 2 || RX ||
|}

== UNI-T UT-D02 ==

The [http://www.uni-trend.com.cn/cp-show.asp?yy=%D6%D0%CE%C4&ProductNO=388 UNI-T UT-D02] is an RS232 cable for various UNI-T multimeters (and rebranded models) with PC connectivity.

'''Hardware''':
* TODO.

''' Works with''':
* UNI-T UT61D/...
* Voltcraft VC820/VC840/...

''' Where to buy''':
* [https://secure.reichelt.de/Multimeter-digital/UT-D01/3/index.html?;ACTION=3;LA=2;ARTICLE=100496;GROUPID=4058;artnr=UT+D01 Reichelt] (€15.95)
* [http://www.conrad.de/ce/de/product/125640/VOLTCRAFT-RS-232-SCHNITTSTELLENADAPTER/SHOP_AREA_17626&promotionareaSearchDetail=005 Conrad/Voltcraft] (€9.95)
* [http://www.pinsonne-elektronik.de/pi10/pd82.html Pinnesonne] (€5.00)
* [http://www.ebay.de/itm/UNI-T-UT-D02-RS232-Data-Cable-/360492337424 eBay, various sellers] (€7.99)

<gallery>
File:Voltcraft dmm rs232 cable.jpg|Cable
File:Voltcraft dmm rs232 cable ir.jpg|Cable, IR
File:Voltcraft dmm rs232 cable open.jpg|Cable, open
File:Voltcraft dmm rs232 cable pcb front.jpg|PCB, front
File:Voltcraft dmm rs232 cable pcb back.jpg|PCB, back
</gallery>

== UNI-T UT-D04 ==

The [http://www.uni-trend.com/UT-D04.html UNI-T UT-D04] (see also [http://www.uni-trend.com.cn/cp-show.asp?yy=%D6%D0%CE%C4&ProductNO=386 uni-trend.com.cn]) is a USB/HID cable for various UNI-T multimeters (and rebranded models) with PC connectivity.

There have been (at least) two versions of this cable, the older one with Hoitek HE2325U USB/HID chip, the newer one using a WCH CH9325 USB/HID chip.

See [[Device cables/Info#UNI-T_UT-D04]] for more details (such as '''lsusb -v''' output) about the cable.

'''Hardware (old version)''':
* Hoitek HE2325U

'''Hardware (new version)''':
* [[WCH CH9325]]

'''Works with''':
* [[UNI-T UT61B]] / [[UNI-T UT61C|UT61C]] / [[UNI-T UT61D|UT61D]] / [[UNI-T UT61E|UT61E]], various other UNI-T DMMs
* [[Voltcraft VC-820]] / [[Voltcraft VC-830|VC-830]] / [[Voltcraft VC-840|VC-840]], various other Voltcraft rebadges of UNI-T DMMs
* [[Tenma 72-7745]] and various other Tenma/Farnell rebadges of UNI-T DMMs

'''Where to buy''':
* [https://secure.reichelt.de/Multimeter-digital/UT-D04/3/index.html?;ACTION=3;LA=2;ARTICLE=97153;GROUPID=4058;artnr=UT+D04 Reichelt] (€9.95)
* [http://www.conrad.de/ce/de/product/120317/Voltcraft-USB-SCHNITTSTELLENADPTER/SHOP_AREA_17626&promotionareaSearchDetail=005 Conrad/Voltcraft] (€25.95)
* [http://www.pinsonne-elektronik.de/pi10/pd78.html Pinnesonne] (€8.90)
* [http://www.ebay.de/itm/UT-D04-USB-INFRARED-INTERFACE-CABLE-FOR-UT71-and-UT81-/180687967854 eBay, various sellers] (€12.37)

<gallery>
File:Uni-t ut61d cable.jpg|Cable
File:Uni-t ut61d cable ir.jpg|Cable, IR
File:Uni-t ut61d usb cable attached.jpg|Attached cable
File:Uni-t ut61d cable open1.jpg|Opened 1
File:Uni-t ut61d cable open2.jpg|Opened 2
File:Uni-t ut61d cable pcb front.jpg|PCB, front
File:Uni-t ut61d cable pcb back.jpg|PCB, back
</gallery>

other cable, but only with different silkscreen (another batch?)

<gallery>
File:UT81-USB_cable.jpg|Cable
File:UT81-USB_cable_led.jpg|Cable, IR
File:UT81-USB_cable_opened.jpg|Opened
File:UT81-USB_cable_front.jpg|PCB, front
File:UT81-USB_cable_back.jpg|PCB, back
</gallery>

Voltcraft sells rebranded, UNI-T made DMMs, and also ships with the same USB/HID cable, but with a Voltcraft logo/marking on it. It is likely that Voltcraft also shipped both the old and new version of the cable at some point.

<gallery>
File:Voltcraft ut-d04 cable.jpg|Voltcraft cable
File:Voltcraft ut-d04 ir.jpg|Voltcraft cable, IR
</gallery>

== V&A VA4000 ==

The [http://www.mastech.com.cn/html/en/products-accessories.htm V&A VA4000] is a USB PC interface cable for various V&A multimeters.

It seems there have been at least two different revisions of the cable. The older one used a Sunplus SPCP825 USB-to-serial chip (see [http://www.mikrocontroller.net/topic/160215#2032176 here], [http://multimeter.schewe.com/ here], or also check the drivers from [http://www.elv.de/digital-multimeter-va18b-mit-pc-link.html here]), the newer revisions use a Prolific PL2303HX chip.

See [[Device cables/Info#V.26A_VA4000]] for more details (such as '''lsusb -vvv''' output) about the cable.

'''Hardware''' (old cable version):

* '''USB to serial chip''': Sunplus SPCP825
* '''Crystal''': ?

'''Hardware''' (new cable version):

* '''USB to serial chip''': Prolific PL2303HX YR0903A
* '''Crystal''': 12MHz

''' Works with''':
* V&A VA18B, V&A VA-38

''' Where to buy''':
* [http://www.komerci.de/shop/product_info.php?products_id=427&cPath=26_42&osCsid=0c0a8cf5d72cd931528b26aeb5af7ce5 Komerci] (€6.50)

Old cable with Sunplus SPCP825 chip:

<gallery>
File:Va va4000 cable sunplus ic 0405.jpg|USB cable
File:Va va4000 cable sunplus ic 0407.jpg|Cable, dismantled
File:Va va4000 cable sunplus ic 0408.jpg|PCB, top
File:Va va4000 cable sunplus ic 0414.jpg|PCB, bottom
</gallery>

New cable with Prolific PL2303HX:

<gallery>
File:Mastech va18b usb cable.jpg|USB cable
File:Mastech va18b usb cable pcb front.jpg|USB cable PCB, front
File:Mastech va18b usb cable pcb back.jpg|USB cable PCB, back
</gallery>

== V&A VA4001 ==

The [http://www.mastech.com.cn/html/en/products-accessories.htm V&A VA4001] is an RS232 PC interface cable for various V&A multimeters.

TODO.

== Victor 86C USB cable ==

The [[Victor 86C]] PC interface cable (doesn't seem to have a specific name or part number) contains a USB/HID chip.

'''Hardware''':

* '''USB/HID chip''': [[Victor_protocol#USB_interface_chip|Unmarked SO-20 chip]]

''' Works with''':
* Victor 86C. Maybe other Victor models(?)

''' Where to buy''':
* The cable ships with the Victor 86C. It's unclear whether it can be bought standalone (without DMM).

<gallery>
File:Victor 86c usb cable.jpg|USB cable
File:Victor 86c usb cable open.jpg|USB cable, open
File:Victor 86c usb cable pcb top.jpg|USB cable PCB, front
File:Victor 86c usb cable pcb bottom.jpg|USB cable PCB, back
</gallery>

More information about the USB chip and the protocol it uses to communicate with the PC can be found on the [[Victor protocol]] page.

= Sound level meters =

== Colead SL-5868P cables ==

Some distributors sell the [[Colead SL-5868P]] sound level meter with a set of two cables: one 3.5mm jack to female DB9, and one male DB9 to USB, which has a Prolific PL-2303 chip in the DB9. This cable does not work; the device's serial port needs a 2.5mm jack.

<gallery>
File:Colead SL5868P cables.jpg|A really bad idea
File:Colead SL5868P cable USB top.jpg|DB9 to USB, top
File:Colead SL5868P cable USB bottom.jpg|DB9 to USB, bottom
File:Colead SL5868P cable serial top.jpg|3.5mm jack to DB9, top
File:Colead SL5868P cable serial bottom.jpg|3.5mm jack to DB9, bottom
</gallery>

The SL-5868P is also available with bluetooth connectivity instead of serial.

== Tondaj SL-814 cable ==

The [[Tondaj SL-814]] sound level meter ships with this USB PC interface cable.

'''Hardware''':
* '''USB to serial chip''': Prolific PL2303HX LFC10073A
* '''Crystal''': 12MHz

''' Works with''':
* [[Tondaj SL-814]] (maybe other Tondaj gear?)

''' Where to buy''':
* The cable ships with the [[Tondaj SL-814]]. It's unclear whether it can be bought standalone (without the sound level meter).

<gallery>
File:Tondaj sl814 cable.jpg|Cable
File:Tondaj sl814 cable connector.jpg|Cable, connector
File:Tondaj sl814 cable open1.jpg|Cable, open
File:Tondaj sl814 cable open2.jpg|Cable, open 2
File:Tondaj sl814 cable pcb top.jpg|PCB, top
File:Tondaj sl814 cable pcb bottom.jpg|PCB, bottom
</gallery>

= Programmable electronic loads =

== M133 ==

The '''M133''' (vendor unknown) cable ships with the [[ATTEN ATZ9711]] programmable electronic load. It's unclear whether this is a custom cable for this device, or a generic RS232 isolator cable.

The 28-pin chip is a standard Prolific PL-2303HX serial-USB chip.

The other chip is presumably an optocoupler, but the vendor/model is unknown.

<gallery>
File:M133 isolated serial-USB cable.jpg
File:M133 isolated serial-USB cable back.jpg
File:M133 isolated serial-USB cable PCB top.jpg
File:M133 isolated serial-USB cable PCB bottom.jpg
File:M133 isolated serial-USB cable chip.jpg
</gallery>

File:UT81-USB cable opened.jpg

2014-01-01T16:56:06Z

Tsaitgaist: USB-HID data cable used for a UNI-T UT61B view of the internal PCB

USB-HID data cable used for a UNI-T UT61B

view of the internal PCB

File:UT81-USB cable led.jpg

2014-01-01T16:55:17Z

Tsaitgaist: USB-HID data cable used for a UNI-T UT61B view of the LED use the receive data from the DMM

== Summary ==
USB-HID data cable used for a UNI-T UT61B

view of the LED use the receive data from the DMM
== Licensing ==
{{CC-BY-SA-3.0}}

File:UT81-USB cable.jpg

2014-01-01T16:54:16Z

Tsaitgaist: USB-HID data cable used for a UNI-T UT61B view of the complete cable

== Summary ==
USB-HID data cable used for a UNI-T UT61B

view of the complete cable
== Licensing ==
{{CC-BY-SA-3.0}}

File:UT81-USB cable back.jpg

2014-01-01T16:53:06Z

Tsaitgaist: /* Summary */

== Summary ==
USB-HID data cable used for a UNI-T UT61B

back side of the PCB

== Licensing ==
{{CC-BY-SA-3.0}}

File:UT81-USB cable front.jpg

2014-01-01T16:52:51Z

Tsaitgaist: /* Summary */

== Summary ==
USB-HID data cable used for a UNI-T UT61B

front side of the PCB

== Licensing ==
{{CC-BY-SA-3.0}}

File:UT81-USB cable back.jpg

2014-01-01T16:46:21Z

Tsaitgaist: USB-HID data cable used for a UNI-T UT61B back side of the PCB

== Summary ==
USB-HID data cable used for a UNI-T UT61B
back side of the PCB
== Licensing ==
{{CC-BY-SA-3.0}}

File:UT81-USB cable front.jpg

2014-01-01T16:45:03Z

Tsaitgaist: USB-HID data cable used for a UNI-T UT61B

== Summary ==
USB-HID data cable used for a UNI-T UT61B
== Licensing ==
{{CC-BY-SA-3.0}}