sigrok - User contributions [en]

Rigol DS1000Z series

2015-03-03T08:22:26Z

Pl4nkton:

{{Infobox oscilloscope
| image =
| name = Rigol DS1000Z Series
| status =
| source_code_dir =
| channels = 4
| samplerate = 1GSa/s (1ch), 500MSa/s (2ch), 250MSa/s (3 or 4 ch)
| bandwidth = 50-100MHz (depending on model)
| vertical_resolution = 8bits
| triggers = edge, pulse, runt, windows, nth edge, slope, video, pattern, delay, timeout, duration, setup/hold, RS232/UART, I²C, SPI
| input_impedance = 1MΩ‖13pF 300V RMS CAT I
| memory = 12/24Mpts (mode/ch-dependent)
| display = 7 Inch WVGA (800x480) 160,000 colours
| connectivity = USB host/device, ethernet (LXI), trigger out, pass/fail out
| features = math: +, —, x, /, FFT, vertical sensitivity: 1 mV/div to 10 V/div
| website = [http://www.rigolna.com/products/digital-oscilloscopes/ds1000Z/ rigolna.com]
}}

The [http://www.rigolna.com/products/digital-oscilloscopes/ds1000Z/ Rigol DS1000Z Series] are 4-channel oscilloscopes with an analog bandwidth of 50-100MHz and 1GSa/s maximum sampling rate.

== Devices ==

{| class="wikitable"
!Model || Bandwidth
|-
|| [[Rigol DS1054Z]] || 50MHz
|-
|| DS1074Z || 70MHz
|-
|| DS1104Z || 100MHz
|}

== Protocol ==

The device uses [[USBTMC]] or LXI via its ethernet port for communication with a host PC. The protocol is based on SCPI commands.

== Resources ==

* [http://www.batronix.com/pdf/Rigol/UserGuide/DS1000Z_UserGuide_EN.pdf Batronix: User manual]
* [http://www.batronix.com/pdf/Rigol/ProgrammingGuide/MSO1000Z_DS1000Z_ProgrammingGuide_EN.pdf Batronix: Programming guide]
* [http://www.flickr.com/photos/eevblog/sets/72157646442125864/ EEVBlog: High resolution images of DS1054Z]

[[Category:Device]]
[[Category:Oscilloscope]]

Rigol DS1054Z/Info

2015-03-03T08:19:55Z

Pl4nkton:

== lsusb ==


$ '''lsusb -v'''
Bus 003 Device 066: ID 1ab1:04ce Rigol Technologies
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1ab1 Rigol Technologies
idProduct 0x04ce
bcdDevice 0.02
iManufacturer 1 Rigol Technologies.
iProduct 2 DS1000Z Series
iSerial 3 DS1ZA123456789
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 254 Application Specific Interface
bInterfaceSubClass 3 Test and Measurement
bInterfaceProtocol 1 TMC
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 80
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered

Rigol DS1054Z/Info

2015-03-03T08:17:54Z

Pl4nkton: Created page with "Bus 003 Device 066: ID 1ab1:04ce Rigol Technologies Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass..."

Bus 003 Device 066: ID 1ab1:04ce Rigol Technologies
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1ab1 Rigol Technologies
idProduct 0x04ce
bcdDevice 0.02
iManufacturer 1 Rigol Technologies.
iProduct 2 DS1000Z Series
iSerial 3 DS1ZA123456789
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 254 Application Specific Interface
bInterfaceSubClass 3 Test and Measurement
bInterfaceProtocol 1 TMC
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 80
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered

Rigol DS1054Z

2015-03-02T22:38:30Z

Pl4nkton:

{{Infobox oscilloscope
| image = [[File:Rigol-ds1054Z mugshot.png|180px]]
| name = Rigol DS1054Z
| status = not supported
| source_code_dir = rigol-ds
| channels = 4
| samplerate = 1GSa/s (1ch), 500MSa/s (2ch), 250MSa/s (3/4ch)
| bandwidth = 50MHz (upgradable up to 100 MHz)
| vertical_resolution = 8bits (12bits HR)
| triggers = edge, pulse, runt, windows, nth edge, slope, video, pattern, delay, timeout, duration, setup/hold, RS232/UART, I²C, SPI
| input_impedance = 1MΩ‖15pF 300V RMS CAT I
| memory = 12Mpts (24Mpts option) (mode/ch-dependent)
| display = 7" 800x480, 160K colors
| connectivity = USB host/device, Ethernet, trigger out, pass/fail out
| features = math: +, —, x, /, FFT, vertical sensitivity: 500µV/div - 10V/div
| website = [http://www.rigolna.com/products/digital-oscilloscopes/ds1004z/ds1054z/ rigolna.com]
}}

The [http://www.rigolna.com/products/digital-oscilloscopes/ds1000Z/ds1054z/ Rigol DS1054Z] is a USB-based, 4-channel oscilloscope with an analog bandwidth of 50MHz and 1GS/s sampling rate.

See [[Rigol DS1054Z/Info]] for more details (such as '''lsusb -v''' output) about the device.

See [[Rigol DS1000Z series]] for information common to all devices in this series.

== Photos ==

<gallery>
</gallery>

== Protocol ==

Example of using SCPI over LAN:
sigrok-cli -d rigol-ds:conn=tcp-raw/192.168.3.16/5555 -l 5 --scan
sigrok-cli -d rigol-ds:conn=tcp-raw/192.168.3.16/5555 --frames 1 -O analog

== More Info ==

[[Category:Device]]
[[Category:Oscilloscope]]
[[Category:Supported]]

Rigol DS1054Z

2015-03-02T22:38:04Z

Pl4nkton: Created page with "{{Infobox oscilloscope | image = 180px | name = Rigol DS1054Z | status = supported | source_code_d..."

{{Infobox oscilloscope
| image = [[File:Rigol-ds1054Z mugshot.png|180px]]
| name = Rigol DS1054Z
| status = supported
| source_code_dir = rigol-ds
| channels = 4
| samplerate = 1GSa/s (1ch), 500MSa/s (2ch), 250MSa/s (3/4ch)
| bandwidth = 50MHz (upgradable up to 100 MHz)
| vertical_resolution = 8bits (12bits HR)
| triggers = edge, pulse, runt, windows, nth edge, slope, video, pattern, delay, timeout, duration, setup/hold, RS232/UART, I²C, SPI
| input_impedance = 1MΩ‖15pF 300V RMS CAT I
| memory = 12Mpts (24Mpts option) (mode/ch-dependent)
| display = 7" 800x480, 160K colors
| connectivity = USB host/device, Ethernet, trigger out, pass/fail out
| features = math: +, —, x, /, FFT, vertical sensitivity: 500µV/div - 10V/div
| website = [http://www.rigolna.com/products/digital-oscilloscopes/ds1004z/ds1054z/ rigolna.com]
}}

The [http://www.rigolna.com/products/digital-oscilloscopes/ds1000Z/ds1054z/ Rigol DS1054Z] is a USB-based, 4-channel oscilloscope with an analog bandwidth of 50MHz and 1GS/s sampling rate.

See [[Rigol DS1054Z/Info]] for more details (such as '''lsusb -v''' output) about the device.

See [[Rigol DS1000Z series]] for information common to all devices in this series.

== Photos ==

<gallery>
</gallery>

== Protocol ==

Example of using SCPI over LAN:
sigrok-cli -d rigol-ds:conn=tcp-raw/192.168.3.16/5555 -l 5 --scan
sigrok-cli -d rigol-ds:conn=tcp-raw/192.168.3.16/5555 --frames 1 -O analog

== More Info ==

[[Category:Device]]
[[Category:Oscilloscope]]
[[Category:Supported]]

Pico Technology PicoScope 5203/Info

2013-01-01T14:39:48Z

Pl4nkton:

== lsusb (before firmware upload) ==


$ '''lsusb -vvv'''
Bus 001 Device 006: ID '''0ce9:1008 pico Technology'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
idVendor 0x0ce9 '''pico Technology'''
idProduct 0x1008
bcdDevice 0.01
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 171
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 6
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 2
bNumEndpoints 6
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 3
bNumEndpoints 6
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0


== After firmware upload ==

Bus 002 Device 021: ID '''0ce9:1008 pico Technology'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0ce9 '''pico Technology'''
idProduct 0x1008
bcdDevice 0.02
iManufacturer 1 '''Pico'''
iProduct 2 '''PicoScope 5000'''
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
(Missing must-be-set bit!)
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)

File:Picoscope 5203 pcb top.jpg

2013-01-01T02:15:00Z

Pl4nkton:

== Licensing == {{PD}}

File:Picoscope 5203 pcb bottom.jpg

2013-01-01T02:14:46Z

Pl4nkton:

== Licensing == {{PD}}

File:Picoscope 5203 front.jpg

2013-01-01T02:14:03Z

Pl4nkton:

== Licensing == {{PD}}

File:Picoscope 5203 back.jpg

2013-01-01T01:37:26Z

Pl4nkton:

== Licensing ==
{{PD}}

File:Picoscope 5203 front.jpg

2013-01-01T01:35:56Z

Pl4nkton:

File:Picoscope 5203 pcb top.jpg

2013-01-01T01:23:32Z

Pl4nkton: Pl4nkton moved page File:Picoscope 5203 pcb front.jpg to File:Picoscope 5203 pcb top.jpg

Pico Technology PicoScope 5203

2013-01-01T01:22:27Z

Pl4nkton: /* Photos */

[[File:Picoscope 5203 front.jpg|thumb|right|PicoScope 5203.]]

The [http://www.picotech.com/picoscope5203-specifications.html Pico Technology PicoScope 5203] is a 2-channel USB-based PC oscilloscope (and spectrum analyzer and data logger and logic analyzer). It supports a bandwidth of 250 MHz. The max. sampling rate (one-shot) is 1 GS/s (one channel mode) or 500 MS/s (two channel mode). The max. sampling rate for repetitive signals is 20 GS/s, the max. sampling rate in continuous streaming mode is 1 MS/s.

See [[Pico Technology PicoScope 5203/Info]] for more details (such as '''lsusb -vvv''' output) about the device.

== Hardware ==

* 2x Micron D9JLR DDR2 SDRAM 512M (32Mx16)
* Xilinx Spartan XC3S400
* Microchip LC24641 EEPROM for usb id
* Cypress CY7C68013A-56PVXC (FX2LP) USB interface
* Texas Instruments ADC08D500 High Performance, Low Power, Dual 8-Bit, 500 MSPS A/D Converter
* Analog Devices AD9742 12-Bit, 210 MSPS TxDAC D/A Converter
* Analog Devices ADCMP562 high speed comparator
* 3x pca9557
* 4x Omron g6h-2-100
* 3x MEDER electronic SILO5-1A72-71DHR

== Photos ==

<gallery>
File:Picoscope 5203 front.jpg|Front
File:Picoscope 5203 back.jpg|Back
File:Picoscope 5203 pcb top.jpg|PCB, front
File:Picoscope 5203 pcb bottom.jpg|PCB, back
</gallery>

== Protocol ==

=== Firmware ===

=== Start acquisition ===

=== Sample format ===

=== End acquisition ===

=== Triggers ===

=== Voltage ranges ===

±100 mV to ±20 V in 8 ranges

== Resources ==

* [http://www.picotech.com/picoscope5200-oscilloscopesoftware.html Vendor software]
* [http://www.picotech.com/softdownloader.html?zeitfaktor=5m0k3m34k1pp3r&os=linux/32bit&soft=libps5000_R1_3_6_6_3.i386&pid=50 Linux drivers]
* [http://www.picotech.com/softdownloader.html?zeitfaktor=5m0k3m34k1pp3r&os=drivers&soft=PS5000sdk&pid=50 SDK]

[[Category:Device]]
[[Category:Oscilloscope]]
[[Category:Planned]]

File:Picoscope 5203 pcb bottom.jpg

2013-01-01T01:22:18Z

Pl4nkton:

File:Picoscope 5203 pcb top.jpg

2013-01-01T01:20:16Z

Pl4nkton:

Supported hardware

2012-12-31T22:50:30Z

Pl4nkton: /* Oscilloscopes */

sigrok is intended as a flexible, cross-platform, and '''hardware-independent''' software suite, i.e., it supports various devices from many different vendors.

Here is a list of currently supported devices (various stages of completeness) and devices we plan to support in the near future.

The lists are sorted by category (supported, in progress, planned), and alphabetically within those categories.

== Logic analyzers ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_supported|ARMFLY Mini-Logic|File:ARMFLY MINI LOGIC.png|is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.}}

{{hwsup_supported|ASIX SIGMA|File:Sigma2_2.png|is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate, and with 256Mbit on-board memory.}}

{{hwsup_supported|Braintechnology USB Interface V2.x|File:Braintechnology_usb_interface_v26.png|is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate.}}

{{hwsup_supported|Braintechnology USB-LPS|File:Braintechnology_usb_lps.png|is a USB-based, 16-channel logic analyzer (and signal generator) with up to 24MHz sampling rate.}}

{{hwsup_supported|ChronoVu LA8|File:Chronovu la8 front.png|is a USB-based, 8-channel logic analyzer with up to 100MHz sampling rate.}}

{{hwsup_supported|CWAV USBee SX|File:Cwav_usbee_sx.png|is a USB-based, 8-channel logic analyzer (and signal generator) with up to 24MHz sampling rate.}}

{{hwsup_progress|Dangerous Prototypes Buspirate|File:Buspirate_v3.png|is a USB-based, 5-channel logic analyzer with up to 1MHz sampling rate. It uses the [http://dangerousprototypes.com/docs/The_Logic_Sniffer%27s_extended_SUMP_protocol extended SUMP protocol]. The Buspirate supports a logic analyzer mode and can thus be used for sample captures, however only at low speeds.}}

{{hwsup_supported|EE Electronics ESLA100|File:Eeelec xla esla100.png|is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.}}

{{hwsup_supported|Lcsoft Mini Board|File:Lcsoft-miniboard-front.png|is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate.}}

{{hwsup_supported|Logic Shrimp|File:logic-shrimp-front.png|is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate. It uses the [http://dangerousprototypes.com/docs/The_Logic_Sniffer%27s_extended_SUMP_protocol extended SUMP protocol].}}

{{hwsup_supported|Openbench Logic Sniffer|File:Openbench logic sniffer front.png|(OLS) is a USB-based (and FPGA-based), 32-channel logic analyzer with up to 100MHz sampling rate and advanced trigger functionality. It is a fully open source device — the circuit design, VHDL code for the FPGA, firmware for the PIC microcontroller and Java-based client software are all freely available. It uses the [http://dangerousprototypes.com/docs/The_Logic_Sniffer%27s_extended_SUMP_protocol extended SUMP protocol].}}

{{hwsup_supported|Robomotic BugLogic 3|File:Robomotic buglogic3.png|is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.}}

{{hwsup_supported|Robomotic MiniLogic|File:Robomotic_minilogic.png|is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.}}

{{hwsup_supported|Saleae Logic|File:Saleae Logic.png|is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.}}

{{hwsup_supported|ZEROPLUS Logic Cube LAP-C(16032)|File:Zeroplus Logic Cube.png| is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate.}}

{{hwsup_progress|RockyLogic Ant8|File:Rockylogic_ant8.png|is a USB-based, 8-channel logic analyzer with up to 500MHz sampling rate.}}

{{hwsup_progress|RockyLogic Ant18e|File:RockyLogic Ant18e.png|is a USB-based, 18-channel logic analyzer with up to 1GHz sampling rate.}}

{{hwsup_planned|Acute PKLA-1216|File:Acute_pkla1216.png|is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate.}}

{{hwsup_planned|Ideofy LA-08|File:Ideofy_la_08.png|is a USB-based, 8-channel logic analyzer with a max. samplerate of 96Msps@2ch (or 60msps@4ch, or 30msps@8ch).}}

{{hwsup_planned|Ikalogic SCANALOGIC-2 PRO|File:Ikalogic_scanalogic2.png|is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate.}}

{{hwsup_planned|Intronix Logicport LA1034|File:Intronix Logicport.png|is a USB-based (and FPGA-based), 34-channel logic analyzer with up to 500MHz sampling rate.}}

{{hwsup_planned|Microchip PICkit2|File:Microchip_pickit2.png|is a USB-based, 3-channel logic analyzer with up to 1MHz sampling rate. The PICkit2 is actually a programmer/debugger for PIC microcontrollers, but it can also be used as logic analyzer.}}

{{hwsup_planned|MiniLA Mockup|File:Minila mockup.jpg|is a USB-based, 32-channel logic analyzer with up to 100MHz sampling rate.}}

{{hwsup_planned|Saleae Logic16|File:Saleae_Logic16_bottom.png|is a USB-based, 16-channel logic analyzer with 100/50/25/12.5MHz sampling rate (at 2/4/8/16 enabled channels).}}

{{hwsup_planned|Sysclk LWLA1016|File:Sysclk lwla1016 front.jpg|is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate.}}

{{hwsup_planned|TechTools DigiView DV1-100|File:Techtools_digiview_dv1-100.png|is a USB-based, 18-channel logic analyzer with 100MHz sampling rate.}}

{{hwsup_planned|ZEROPLUS LAP-16128U|File:Zeroplus_lap-16128u.png|is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate.}}

{{hwsup_planned|ZEROPLUS Logic Cube LAP-C(322000)|File:Sigrok_logo_no_text_transparent_512.png|is a USB-based, 32-channel logic analyzer with a max. samplerate of 200MHz.}}

{{hwsup_planned|ZLG LA1032|File:Zlg_la1032.png|is a USB-based, 32-channel, 100MHz logic analyzer.}}

|}

== Mixed-signal devices ==

Devices which can be used as both logic analyzer and oscilloscopes.

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_supported|ARMFLY AX-Pro|File:AX-Pro.JPG|is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels.

'''Note:''' Only the logic analyzer functionality is supported so far, analog support is work in progress.}}

{{hwsup_supported|EE Electronics ESLA201A|File:Esla201a.JPG|is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels.

'''Note:''' Only the logic analyzer functionality is supported so far, analog support is work in progress.}}

{{hwsup_supported|XZL Studio DX|File:Sigrok_logo_no_text_transparent_512.png|is a USB-based, 16-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels.

'''Note:''' Only the logic analyzer functionality is supported so far, analog support is work in progress.}}

{{hwsup_progress|Link Instruments MSO-19|File:Link Instruments MSO-19 front.png|is a USB-based, 1-channel 2GSa/s oscilloscope, 8-channel 200MSa/s logic analyzer, 100MSa/s pattern generator and a [https://en.wikipedia.org/wiki/Time-domain_reflectometer TDR].}}

{{hwsup_planned|Agilent MSO7104A|File:Agilent_MSO7104A.jpg|is a standalone, 4-channel mixed-signal digital storage oscilloscope (1GHz bandwidth, 4GSa/s samplerate, 16-channel logic analyzer).}}

{{hwsup_planned|Digilent Analog Discovery|File:Digilent_analog-discovery.jpg|is a USB-based 100MSa/s dual channel oscilloscope, function generator, logic analyzer and pattern generator.}}

{{hwsup_planned|Meilhaus MEphisto Scope1|File:Meilhaus_mephisto_scope1.png|is a USB-based multifunction acquisition device.}}

{{hwsup_planned|PoLabs PoScope Basic2|File:Polabs_poscope_basic2.png|is a USB-based, 16-channel logic analyzer (plus oscilloscope, signal/pattern generator, and more) with up to 8MHz sampling rate.}}

{{hwsup_planned|QuantAsylum QA100|File:QA100.png|is a USB-based, mixed-mode oscilloscope with 12 digital inputs, 2 analog, 1 trigger and 1 audio waveform generator.}}

{{hwsup_planned|Rigol VS5202D|File:Rigol_VS5202D_Full.jpg|is a USB-based, 2-channel analog oscilloscope (400MSa/S, 200MHz bandwidth) and 16-channel logic analyzer (200MHz sampling rate).}}

|}

== Oscilloscopes ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_supported|Fluke ScopeMeter 199B|File:Fluke_Scopemeter_199B.png|is a handheld combined multimeter and oscilloscope. Only the multimeter functionality is supported; the device's slow communication speed does not allow for properly supporting it as an oscilloscope in sigrok.}}

{{hwsup_supported|Hantek DSO-2090|File:Hantek DSO-2090.png|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 40MHz and 100MS/s sampling rate.}}

{{hwsup_progress|Hantek DSO-5200A|File:Hantek dso-5200a device front.png|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 250MS/s sampling rate.}}

{{hwsup_progress|Velleman PCSU1000|File:Velleman PCSU1000.png|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 50MHz and 1GS/s sampling rate.}}

{{hwsup_planned|Hantek DSO-1200|File:Sigrok_logo_no_text_transparent_512.png|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 500MS/s sampling rate (and a multimeter).}}

{{hwsup_planned|Fluke ScopeMeter 123|File:Fluke scopemeter123.png|is a handheld, 2-channel oscilloscope with an analog bandwidth of 20MHz and 25MS/s sampling rate.}}

{{hwsup_planned|Focussz Fosc21|File:Focussz fosc21 back.jpg|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 3kHz and a sampling rate of 8kHz (1 channel) / 4kHz (2 channels).}}

{{hwsup_planned|Nexus-Computing OsciPrime|File:OsciPrime.png|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 3.3MHz-8MHz. It is 100% open source hardware and software.}}

{{hwsup_planned|Pico Technology PicoScope 2203|File:Picoscope 2203 front.jpg|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 5MHz and 40/20MS/s sampling rate (1-/2-channel one-shot mode).}}

{{hwsup_planned|Pico Technology PicoScope 2205|File:PicoScope 2205 front.jpg|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 25MHz and 200/100MS/s sampling rate (1-/2-channel one-shot mode).}}

{{hwsup_planned|Pico Technology PicoScope 3206|File:Picoscope 3206.png|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 200/100MS/s sampling rate (1-/2-channel one-shot mode).}}

{{hwsup_planned|Pico Technology PicoScope 5203|File:Picoscope 5203.png|is a USB-based, 2-channel oscilloscope with an analog bandwidth of 250MHz and 1/0,5GS/s sampling rate (1-/2-channel one-shot mode).}}

{{hwsup_planned|Rigol DS1052E|File:Rigol DS1052E.png|is a 50MHz, 1GSa/s, 2-channel digital storage oscilloscope. It can be upgraded to 100MHz analog bandwidth with a software modification.}}

{{hwsup_planned|USB-DUXfast|File:Usbduxfast.png|is an USB-based analog data acquisition device. It supports up to 16 channels at 3 MHz.}}

{{hwsup_planned|Voltcraft DSO-3062C|File:Voltcraft DSO-3062C.png|is a 60MHz, 1GSa/s, 2-channel digital storage oscilloscope. It can be upgraded to 200MHz analog bandwidth with a software modification.}}

|}

== Multimeters ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_supported|Agilent U1231A|File:Sigrok_logo_no_text_transparent_512.png|is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity.}}

{{hwsup_supported|Agilent U1232A|File:Agilent U1232A.png|is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity.}}

{{hwsup_supported|Agilent U1233A|File:Sigrok_logo_no_text_transparent_512.png|is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity.}}

{{hwsup_progress|Brymen BM857|File:Bm_857_mugshot_500000.png|is a 50000 counts (500000 DC), CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 connectivity.}}

{{hwsup_supported|Digitek DT4000ZC|File:Digitek_dt4000zc_device_front.png|is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity.}}

{{hwsup_supported|Fluke 187/189|File:Fluke 187.png|are 50000 counts, handheld digital multimeters with RS232 connectivity.}}

{{hwsup_supported|Fluke 287/289|File:Fluke 287.png|are 50000 counts handheld digital multimeters with RS232 connectivity.}}

{{hwsup_supported|MASTECH MAS345|File:Mastech mas345 device front.png|is a 4000 counts, CAT II handheld digital multimeter with RS232 connectivity.}}

{{hwsup_supported|PCE PCE-DM32|File:Pce-pce-dm32.png|is a 4000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 connectivity.}}

{{hwsup_supported|PeakTech 3410|File:Metex_me-31.png|is a 4000 counts, CAT II (1000V) handheld digital multimeter with RS232 connectivity.}}

{{hwsup_supported|PeakTech 4370|File:Peaktech 4370 device front.png|is a 2000 counts, CAT II (1000V) handheld digital multimeter with RS232 connectivity.}}

{{hwsup_supported|RadioShack 22-168|File:Rs_22_168_mugshot.png|is a 2000 counts, handheld digital multimeter with RS232 connectivity.}}

{{hwsup_supported|RadioShack 22-812|File:radioshack_22_812_front.png|is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity.}}

{{hwsup_supported|TekPower TP4000ZC|File:Tp4000zc_front.png|is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity.}}

{{hwsup_supported|UNI-T UT61D|File:Uni t ut61d device.png|is a 6000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity.}}

{{hwsup_supported|V&A VA18B|File:Va_va18b.png|is a 6000 counts, CAT II (1000V) handheld digital multimeter with USB connectivity.}}

{{hwsup_supported|Victor 86C|File:Victor 86c device front.png|is a 4000 counts, CAT III (1000V) handheld digital multimeter with USB connectivity.}}

{{hwsup_supported|Victor 70C|File:Victor 70C.png|is a 4000 counts, CAT II handheld digital multimeter with USB connectivity.}}

{{hwsup_supported|Voltcraft VC-820|File:Voltcraft vc820 device.png|is a 4000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity.}}

{{hwsup_progress|UNI-T UT61E|File:Old ver front.png|is a 22000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity.}}

{{hwsup_progress|Voltcraft VC-840|File:Voltcraft vc840 device front.png|is a 4000 counts, CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity.}}

{{hwsup_planned|Escort 179|File:Escort 179 device front.png|is a 10000 counts, handheld digital multimeter with RS232 connectivity.}}

{{hwsup_planned|MASTECH M9803R|File:800px-Mastech m9803r device front.png|is a 4000 counts, CAT II (1000V) digital bench multimeter with RS232 connectivity.}}

{{hwsup_planned|Protek 6500|File:Sigrok_logo_no_text_transparent_512.png|is a 50000 counts handheld digital multimeter with RS232 connectivity.}}

{{hwsup_planned|Voltcraft M-4660A|File:Voltcraft m4660a device front.png|is a 20000 counts, handheld digital multimeter with RS232 connectivity.}}

|}

== LCR meters ==

TODO.

== Sound level meters ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_supported|Colead SL-5868P|File:Colead SL-5868P.png|is a sound level meter with RS232 connectivity.}}

{{hwsup_supported|Tondaj SL-814|File:Tondaj sl-814.png|is a sound level meter with USB connectivity.}}

{{hwsup_planned|CEM DT-8852|File:CEM DT-8852.png|is an IEC 61672-1 class 2-compliant sound level meter with USB connectivity.}}

{{hwsup_planned|PCE PCE-222|File:Pce_pce-222_front.png|is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity. }}

{{hwsup_planned|Voltcraft DL-160S|File:Voltcraft_dl_160s.png|is a sound level meter with USB connectivity.}}

|}

== Thermometers ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_supported|Lascar Electronics EL-USB-2|File:EL-USB-2.png|is a USB-based temperature and humidity logger.}}

{{hwsup_planned|PCE PCE-222|File:Pce_pce-222_front.png|is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity. }}

{{hwsup_planned|RDing TEMPer|File:Rding temper front.png|is a USB-based temperature logger.}}

{{hwsup_planned|RDing TEMPer Gold|File:Rding temper gold device front.png|is a USB-based temperature logger.}}

{{hwsup_planned|RDing TEMPer1|File:Rding temper1 device front.png|is a USB-based temperature logger.}}

{{hwsup_planned|RDing TEMPer1K2|File:Pcsensor temper1k2 front.jpg|is a USB-based temperature logger.}}

{{hwsup_planned|Voltcraft DL-120TH|File:Voltcraft dl-120th front.jpg|is a USB-based temperature logger.}}

{{hwsup_planned|Voltcraft DL-140TH|File:Voltcraft_dl-140th.png|is a USB-based temperature logger.}}

{{hwsup_planned|UNI-T UT325|File:Uni-t ut325 front.png|is a dual thermocouple logging thermometer.}}

|}

== Hygrometers ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_planned|PCE PCE-222|File:Pce_pce-222_front.png|is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity. }}

|}

== Anemometers ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_planned|MASTECH MS6252B|File:Mastech ms6252b device front.jpg|an anemometer with USB connectivity.}}

|}

== Light meters ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_planned|Lutron YK-2005LX|File:Lutron YK-2005LX.png|is a light meter with RS232 connectivity.}}

{{hwsup_planned|PCE PCE-222|File:Pce_pce-222_front.png|is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity. }}

|}

== Dataloggers ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_supported|Lascar Electronics EL-USB-CO|File:EL-USB-CO.png|is a standalone carbon monoxide (CO) logger.}}

{{hwsup_planned|GSG Indoor Air Monitor|File:Gsg_indoor_air_monitor.png|is a USB-based air quality monitor.}}

{{hwsup_planned|MAUL studio i|File:Maul_studio_i.png|is an RS232-based weighing scale.}}

{{hwsup_planned|Voltcraft CO-20|File:Voltcraft co-20 front.jpg|is a USB-based air quality monitor.}}

|}

== Function generators ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_planned|Hantek DDS-3X25|File:Hantek DDS-3X25 top.png|is a 25MHz PC-based function generator (requires a USB connection to work).}}

{{hwsup_planned|Siglent SDG1010|File:Siglent sdg1010 device front 8116.png|is a 10MHz function generator with USB connectivity.}}

|}

== Power supplies ==

TODO

== GPIB interfaces ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

{{hwsup_planned|Beiming S82357|File:Beiming_s82357.png|is a USB-based, hardware-implemented [[GPIB]] interface (a clone of the [http://www.home.agilent.com/en/pd-851808-pn-82357B/usb-gpib-interface-high-speed-usb-20 Agilent 82357B USB/GPIB interface]).}}

{{hwsup_planned|ICS 488-USB|File:ICS 488-USB.png|is a USB-based, hardware-implemented [[GPIB]] interface.}}

{{hwsup_planned|GPIB-USB 82357B clone|File:GPIB-USB 82357B clone.png|is a USB-based, hardware-implemented [[GPIB]] interface (a clone of the [http://www.home.agilent.com/en/pd-851808-pn-82357B/usb-gpib-interface-high-speed-usb-20 Agilent 82357B USB/GPIB interface]).}}

{{hwsup_planned|National Instruments GPIB-ENET|File:NI GPIB-ENET.png|is an Ethernet-based, hardware-implemented [[GPIB]] interface.}}

{{hwsup_planned|National Instruments GPIB-USB-HS|File:NI GPIB-USB-HS.png|is a USB-based, hardware-implemented [[GPIB]] interface.}}

{{hwsup_planned|Prologix GPIB-USB|File:Prologix-usb.png|is a USB-based, firmware-implemented [[GPIB]] interface.}}

|}

== Potential other candidates ==

If you own any other logic analyzers (or oscilloscopes, multimeters, dataloggers, etc.) and want to add support for them in sigrok (or donate/lend devices to developers), please let us know. We're always happy to add more hardware support! Contact [mailto:bert@biot.com Bert Vermeulen] and [mailto:uwe@hermann-uwe.de Uwe Hermann] if you want to help out.

__FORCETOC__

Oscilloscope comparison

2012-12-31T22:48:53Z

Pl4nkton:

This is an alphabetically ordered table of various [https://en.wikipedia.org/wiki/Oscilloscope oscilloscopes] which can log data to your PC via USB, RS232, GPIB, and so on. We do '''not''' list devices without PC connectivity, as those are not really useful for sigrok.

This page lists commercial and non-commercial devices with a short overview of their capabilities. We list all kinds of devices here, not only [[Supported_hardware#Oscilloscopes|those supported by sigrok]].

You should '''not''' use the information here as the sole source for any buying decisions, this is just meant for informational purposes. Please carefully check the vendor websites if you intend to buy any hardware.

{| border="0" width="100%" style="font-size: smaller; white-space=nowrap;" class="alternategrey sortable sigroktable"
|-
!Device
!Type
!Channels
!Bandwidth
!Samplerate
!Price

|-
| [[Hantek DSO-1200]]
| handheld
| 2
| 200MHz
| 500MS/s
| [http://www.amazon.com/Dso1200-Digital-Handheld-Oscilloscope-Channel/dp/B00A3LQOUG/ref=sr_1_1?s=industrial&ie=UTF8&qid=1353782406&sr=1-1&keywords=DSO-1200 $660]

|-
| [[Hantek DSO-2090]]
| USB scope
| 2
| 40MHz
| 100MS/s
| [http://www.amazon.com/Hantek-Based-Digital-Storage-Oscilloscope/dp/B0036FZRU4 $190]

|-
| [[Hantek DSO-5200A]]
| USB scope
| 2
| 200MHz
| 250MS/s
| [http://www.amazon.com/Hantek-Based-Digital-Storage-Oscilloscope/dp/B0036GYLUU/ref=sr_1_2?ie=UTF8&qid=1353782359&sr=8-2&keywords=DSO-5200a $340]

|-
| [http://www.hantek.com/english/produce_list.asp?unid=133 Hantek DSO5062BM]Note 1
| standalone
| 2
| 60MHz/200MHz
| 1GSa/s
| [http://www.aliexpress.com/store/product/All-New-DSO5062BM-Hantek-Digital-Storage-Oscilloscope-2channels-60MHz-1GSa-s-7-Color-Display-2M-Record/907896_625569558.html $500]

|-
| [[Fluke ScopeMeter 123]]
| handheld
| 2
| 20MHz
| 25MSa/s
| [http://www.amazon.com/Fluke-003-Industrial-ScopeMeter-Frequency/dp/B000VRJFMG $1290]

|-
| [[Fluke ScopeMeter 199B]]
| handheld
| 2
| 200MHz
| 2.5GSa/s
| EOL

|-
| [[Focussz Fosc21]]
| USB-scope
| 1/2
| 3kHz
| 8kHz/4kHz
| ?

|-
| [[Nexus-Computing OsciPrime]]
| USB-scope
| 2
| 3.3MHz-8MHz
| ?
| [http://www.osciprime.com/index.php?p=preorder 270 CHF]

|-
| [[Pico Technology PicoScope 2203]]
| USB-scope
| 1/2
| 5MHz
| 40/20 MSa/s
| EOL

|-
| [[Pico Technology PicoScope 2205]]
| USB-scope
| 1/2
| 25MHz
| 200/100 MSa/s
| [http://www.picotech.com/picoscope2000.html £250]

|-
| [[Pico Technology PicoScope 3206]]
| USB-scope
| 1/2
| 200MHz
| 200/100 MSa/s
| EOL

|-
| [[Pico Technology PicoScope 5203]]
| USB-scope
| 1/2
| 250MHz
| 1/0,5 GSa/s
| €1.445,95

|-
| [[Rigol DS1052E]]
| standalone
| 2
| 50MHz/100MHz
| 1GSa/s
| [http://www.batronix.com/shop/oscilloscopes/Rigol-DS1052E.html €269.-]

|-
| [http://www.velleman.eu/products/view/?id=377622 Velleman PCSGU250]
| USB
| 2
| 12MHz
| 25MHz
| [http://www.amazon.de/Velleman-PCSGU250/dp/B001WRMAN0/ref=sr_1_1?ie=UTF8&qid=1351871740&sr=8-1 €144]

|-
| [http://www.velleman.eu/products/view/?id=407512 Velleman PCSU200]
| USB
| 2
| 12MHz
| 25MHz
| [http://www.amazon.com/Velleman-PCSU200-OSCILLOSCOPE-SIGNAL-GENERATOR/dp/B008SS2OFK $141]

|-
| [[Velleman PCSU1000]]
| USB
| 2
| 60MHz
| 50MHz
| [http://www.kitsusa.net/phpstore/html/VELLEMAN-PCSU1000-USB-PC-OSCILLOSCOPE-1393.html $300]

|-
| [[Voltcraft DSO-3062C]]Note 1
| standalone
| 2
| 60MHz/200MHz
| 1GSa/s
| [http://www.conrad.de/ce/de/product/122464/VOLTCRAFT-DSO-3062C-DIGITAL-OSZILLOSKOP/1113030 €299.-]

|}

Notes:


1 [[Voltcraft DSO-3062C]] = [http://www.hantek.com/english/produce_list.asp?unid=133 Hantek DSO5062BM]. 


== Internal details ==

{| border="0" style="font-size: smaller;" class="alternategrey sortable sigroktable"
|-
!Device
!Interface
!Interface chip
!Protocol
!MCU/CPU
!Programmable logic
!Analog chips

|-
| [[Hantek DSO-1200]]
| USB
| ?
| ?
| ?
| ?
| ?

|-
| [[Hantek DSO-2090]]
| USB
| Cypress FX2LP
| custom
| ?
| Xilinx XC95288XL
| ?

|-
| [[Hantek DSO-5200A]]
| USB
| Cypress FX2LP
| custom
| ?
| Unknown FPGA/CPLD
| ?

|-
| [http://www.hantek.com/english/produce_list.asp?unid=133 Hantek DSO5062BM]Note 1
| USB
| ?
| custom
| Samsung S3C2440
| ?
| ?

|-
| [[Fluke ScopeMeter 123]]
| USB, RS232
| ?
| ?
| ?
| ?
| ?

|-
| [[Fluke ScopeMeter 199B]]
| USB, RS232
| ?
| ?
| ?
| ?
| ?

|-
| [[Focussz Fosc21]]
| USB
| ?
| ?
| ?
| —
| ?

|-
| [[Nexus-Computing OsciPrime]]
| USB
| ?
| ?
| ?
| ?
| ?

|-
| [[Pico Technology PicoScope 2203]]
| USB
| Cypress FX2LP
| custom
| ?
| Xilinx Spartan XC3S250E
| Analog Devices AD9288, AD8132

|-
| [[Pico Technology PicoScope 2205]]
| USB
| Cypress FX2LP
| custom
| ?
| Xilinx Spartan XC3S250E
| Analog Devices AD9288, AD8132

|-
| [[Pico Technology PicoScope 3206]]
| USB
| Cypress FX2LP
| custom
| ?
| Xilinx Spartan-II XC2S30
| Analog Devices AD9215

|-
| [[Rigol DS1052E]]
| USB, RS232
| Philips ISP1362BD
| USBTMC
| Analog Devices ADSP-BF531
| Altera Cyclone III EP3C5F256C8N, Lattice Mach XO LCMXO256C
| Analog Devices AD9288

|-
| [[Velleman PCSU1000]]
| USB
| FTDI FT245BL
| custom
| ?
| Xilinx XC3S50
| ?

|-
| [[Voltcraft DSO-3062C]]
| USB
| ?
| custom
| Samsung S3C2440
| Altera MAX-II EPM240T100C5N, Altera Cyclone III FPGA
| 4x Analog Devices AD9288, 2x AD8370, 1x ADCMP562

|}

Notes:


1 [[Voltcraft DSO-3062C]] = [http://www.hantek.com/english/produce_list.asp?unid=133 Hantek DSO5062BM].

Oscilloscope comparison

2012-12-31T22:43:19Z

Pl4nkton:

This is an alphabetically ordered table of various [https://en.wikipedia.org/wiki/Oscilloscope oscilloscopes] which can log data to your PC via USB, RS232, GPIB, and so on. We do '''not''' list devices without PC connectivity, as those are not really useful for sigrok.

This page lists commercial and non-commercial devices with a short overview of their capabilities. We list all kinds of devices here, not only [[Supported_hardware#Oscilloscopes|those supported by sigrok]].

You should '''not''' use the information here as the sole source for any buying decisions, this is just meant for informational purposes. Please carefully check the vendor websites if you intend to buy any hardware.

{| border="0" width="100%" style="font-size: smaller; white-space=nowrap;" class="alternategrey sortable sigroktable"
|-
!Device
!Type
!Channels
!Bandwidth
!Samplerate
!Price

|-
| [[Hantek DSO-1200]]
| handheld
| 2
| 200MHz
| 500MS/s
| [http://www.amazon.com/Dso1200-Digital-Handheld-Oscilloscope-Channel/dp/B00A3LQOUG/ref=sr_1_1?s=industrial&ie=UTF8&qid=1353782406&sr=1-1&keywords=DSO-1200 $660]

|-
| [[Hantek DSO-2090]]
| USB scope
| 2
| 40MHz
| 100MS/s
| [http://www.amazon.com/Hantek-Based-Digital-Storage-Oscilloscope/dp/B0036FZRU4 $190]

|-
| [[Hantek DSO-5200A]]
| USB scope
| 2
| 200MHz
| 250MS/s
| [http://www.amazon.com/Hantek-Based-Digital-Storage-Oscilloscope/dp/B0036GYLUU/ref=sr_1_2?ie=UTF8&qid=1353782359&sr=8-2&keywords=DSO-5200a $340]

|-
| [http://www.hantek.com/english/produce_list.asp?unid=133 Hantek DSO5062BM]Note 1
| standalone
| 2
| 60MHz/200MHz
| 1GSa/s
| [http://www.aliexpress.com/store/product/All-New-DSO5062BM-Hantek-Digital-Storage-Oscilloscope-2channels-60MHz-1GSa-s-7-Color-Display-2M-Record/907896_625569558.html $500]

|-
| [[Fluke ScopeMeter 123]]
| handheld
| 2
| 20MHz
| 25MSa/s
| [http://www.amazon.com/Fluke-003-Industrial-ScopeMeter-Frequency/dp/B000VRJFMG $1290]

|-
| [[Fluke ScopeMeter 199B]]
| handheld
| 2
| 200MHz
| 2.5GSa/s
| EOL

|-
| [[Focussz Fosc21]]
| USB-scope
| 1/2
| 3kHz
| 8kHz/4kHz
| ?

|-
| [[Nexus-Computing OsciPrime]]
| USB-scope
| 2
| 3.3MHz-8MHz
| ?
| [http://www.osciprime.com/index.php?p=preorder 270 CHF]

|-
| [[Pico Technology PicoScope 2203]]
| USB-scope
| 1/2
| 5MHz
| 40/20 MSa/s
| EOL

|-
| [[Pico Technology PicoScope 2205]]
| USB-scope
| 1/2
| 25MHz
| 200/100 MSa/s
| [http://www.picotech.com/picoscope2000.html £250]

|-
| [[Pico Technology PicoScope 3206]]
| USB-scope
| 1/2
| 200MHz
| 200/100 MSa/s
| EOL

|-
| [[Pico Technology PicoScope 5203]]
| USB-scope
| 1/2
| 250MHz
| 1/0,5 GSa/s
|

|-
| [[Rigol DS1052E]]
| standalone
| 2
| 50MHz/100MHz
| 1GSa/s
| [http://www.batronix.com/shop/oscilloscopes/Rigol-DS1052E.html €269.-]

|-
| [http://www.velleman.eu/products/view/?id=377622 Velleman PCSGU250]
| USB
| 2
| 12MHz
| 25MHz
| [http://www.amazon.de/Velleman-PCSGU250/dp/B001WRMAN0/ref=sr_1_1?ie=UTF8&qid=1351871740&sr=8-1 €144]

|-
| [http://www.velleman.eu/products/view/?id=407512 Velleman PCSU200]
| USB
| 2
| 12MHz
| 25MHz
| [http://www.amazon.com/Velleman-PCSU200-OSCILLOSCOPE-SIGNAL-GENERATOR/dp/B008SS2OFK $141]

|-
| [[Velleman PCSU1000]]
| USB
| 2
| 60MHz
| 50MHz
| [http://www.kitsusa.net/phpstore/html/VELLEMAN-PCSU1000-USB-PC-OSCILLOSCOPE-1393.html $300]

|-
| [[Voltcraft DSO-3062C]]Note 1
| standalone
| 2
| 60MHz/200MHz
| 1GSa/s
| [http://www.conrad.de/ce/de/product/122464/VOLTCRAFT-DSO-3062C-DIGITAL-OSZILLOSKOP/1113030 €299.-]

|}

Notes:


1 [[Voltcraft DSO-3062C]] = [http://www.hantek.com/english/produce_list.asp?unid=133 Hantek DSO5062BM]. 


== Internal details ==

{| border="0" style="font-size: smaller;" class="alternategrey sortable sigroktable"
|-
!Device
!Interface
!Interface chip
!Protocol
!MCU/CPU
!Programmable logic
!Analog chips

|-
| [[Hantek DSO-1200]]
| USB
| ?
| ?
| ?
| ?
| ?

|-
| [[Hantek DSO-2090]]
| USB
| Cypress FX2LP
| custom
| ?
| Xilinx XC95288XL
| ?

|-
| [[Hantek DSO-5200A]]
| USB
| Cypress FX2LP
| custom
| ?
| Unknown FPGA/CPLD
| ?

|-
| [http://www.hantek.com/english/produce_list.asp?unid=133 Hantek DSO5062BM]Note 1
| USB
| ?
| custom
| Samsung S3C2440
| ?
| ?

|-
| [[Fluke ScopeMeter 123]]
| USB, RS232
| ?
| ?
| ?
| ?
| ?

|-
| [[Fluke ScopeMeter 199B]]
| USB, RS232
| ?
| ?
| ?
| ?
| ?

|-
| [[Focussz Fosc21]]
| USB
| ?
| ?
| ?
| —
| ?

|-
| [[Nexus-Computing OsciPrime]]
| USB
| ?
| ?
| ?
| ?
| ?

|-
| [[Pico Technology PicoScope 2203]]
| USB
| Cypress FX2LP
| custom
| ?
| Xilinx Spartan XC3S250E
| Analog Devices AD9288, AD8132

|-
| [[Pico Technology PicoScope 2205]]
| USB
| Cypress FX2LP
| custom
| ?
| Xilinx Spartan XC3S250E
| Analog Devices AD9288, AD8132

|-
| [[Pico Technology PicoScope 3206]]
| USB
| Cypress FX2LP
| custom
| ?
| Xilinx Spartan-II XC2S30
| Analog Devices AD9215

|-
| [[Rigol DS1052E]]
| USB, RS232
| Philips ISP1362BD
| USBTMC
| Analog Devices ADSP-BF531
| Altera Cyclone III EP3C5F256C8N, Lattice Mach XO LCMXO256C
| Analog Devices AD9288

|-
| [[Velleman PCSU1000]]
| USB
| FTDI FT245BL
| custom
| ?
| Xilinx XC3S50
| ?

|-
| [[Voltcraft DSO-3062C]]
| USB
| ?
| custom
| Samsung S3C2440
| Altera MAX-II EPM240T100C5N, Altera Cyclone III FPGA
| 4x Analog Devices AD9288, 2x AD8370, 1x ADCMP562

|}

Notes:


1 [[Voltcraft DSO-3062C]] = [http://www.hantek.com/english/produce_list.asp?unid=133 Hantek DSO5062BM].

Pico Technology PicoScope 5203

2012-12-31T22:26:42Z

Pl4nkton:

[[File:Picoscope 5203 front.jpg|thumb|right|PicoScope 5203.]]

The [http://www.picotech.com/picoscope5203-specifications.html Pico Technology PicoScope 5203] is a 2-channel USB-based PC oscilloscope (and spectrum analyzer and data logger and logic analyzer). It supports a bandwidth of 250 MHz. The max. sampling rate (one-shot) is 1 GS/s (one channel mode) or 500 MS/s (two channel mode). The max. sampling rate for repetitive signals is 20 GS/s, the max. sampling rate in continuous streaming mode is 1 MS/s.

See [[Pico Technology PicoScope 5203/Info]] for more details (such as '''lsusb -vvv''' output) about the device.

== Components ==
* 2 x Micron D9JLR DDR2 SDRAM 512M (32Mx16)
* Xilinx Spartan XC3S400
* microchip LC24641 EEPROM for usb id
* Cypress CY7C68013A-56PVXC (FX2) USB interface
* Texas Instruments ADC08D500 High Performance, Low Power, Dual 8-Bit, 500 MSPS A/D Converter
* Analog Devices AD9742 12-Bit, 210 MSPS TxDAC® D/A Converter
* Analog Devices ADCMP562 high speed comparator
* 3 x pca9557
* 4 x omron g6h-2-100
* 3 x MEDER electronic SILO5-1A72-71DHR

== More photos ==

<gallery>
File:Picoscope 5203 front.jpg|Front
File:Picoscope 5203 back.jpg|Back
File:Picoscope 5203 pcb front.jpg|PCB front
File:Picoscope 5203 pcb back.jpg|PCB back
</gallery>

== Protocol ==

=== Firmware ===

=== Start acquisition ===

=== Sample format ===

=== End acquisition ===

=== Triggers ===

=== Voltage ranges ===

±100 mV to ±20 V in 8 ranges

[[Category:Device]]
[[Category:Oscilloscope]]
[[Category:Planned]]

Pico Technology PicoScope 5203/Info

2012-12-31T22:10:12Z

Pl4nkton: Created page with "Bus 001 Device 006: ID 0ce9:1008 pico Technology Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass ..."

Bus 001 Device 006: ID 0ce9:1008 pico Technology
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
idVendor 0x0ce9 pico Technology
idProduct 0x1008
bcdDevice 0.01
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 171
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 6
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 2
bNumEndpoints 6
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 3
bNumEndpoints 6
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0

Pico Technology PicoScope 5203

2012-12-31T21:40:25Z

Pl4nkton: /* Voltage ranges */

[[File:Picoscope 5203 front.jpg|thumb|right|PicoScope 5203.]]

The [http://www.picotech.com/picoscope5203-specifications.html Pico Technology PicoScope 5203] is a 2-channel USB-based PC oscilloscope (and spectrum analyzer and data logger and logic analyzer). It supports a bandwidth of 250 MHz. The max. sampling rate (one-shot) is 1 GS/s (one channel mode) or 500 MS/s (two channel mode). The max. sampling rate for repetitive signals is 20 GS/s, the max. sampling rate in continuous streaming mode is 1 MS/s.

See [[Pico Technology PicoScope 5203/Info]] for more details (such as '''lsusb -vvv''' output) about the device.

== Components ==
* 2 x Micron D9JLR DDR2 SDRAM 512M (32Mx16)
* Xilinx Spartan XC3S400
* Cypress CY7C68013A-56PVXC
* Texas Instruments ADC08D500 High Performance, Low Power, Dual 8-Bit, 500 MSPS A/D Converter
* Analog Devices AD9742 12-Bit, 210 MSPS TxDAC® D/A Converter
* Analog Devices ADCMP562 high speed comparator
* 3 x pca9557
* 4 x omron g6h-2-100

== More photos ==

<gallery>
File:Picoscope 5203 front.jpg|Front
File:Picoscope 5203 back.jpg|Back
File:Picoscope 5203 pcb front.jpg|PCB front
File:Picoscope 5203 pcb back.jpg|PCB back
</gallery>

== Protocol ==

=== Firmware ===

=== Start acquisition ===

=== Sample format ===

=== End acquisition ===

=== Triggers ===

=== Voltage ranges ===

±100 mV to ±20 V in 8 ranges

[[Category:Device]]
[[Category:Oscilloscope]]
[[Category:Planned]]

Pico Technology PicoScope 5203

2012-12-31T21:39:23Z

Pl4nkton: Created page with "PicoScope 5203. The [http://www.picotech.com/picoscope5203-specifications.html Pico Technology PicoScope 5203] is a 2-channel US..."

[[File:Picoscope 5203 front.jpg|thumb|right|PicoScope 5203.]]

The [http://www.picotech.com/picoscope5203-specifications.html Pico Technology PicoScope 5203] is a 2-channel USB-based PC oscilloscope (and spectrum analyzer and data logger and logic analyzer). It supports a bandwidth of 250 MHz. The max. sampling rate (one-shot) is 1 GS/s (one channel mode) or 500 MS/s (two channel mode). The max. sampling rate for repetitive signals is 20 GS/s, the max. sampling rate in continuous streaming mode is 1 MS/s.

See [[Pico Technology PicoScope 5203/Info]] for more details (such as '''lsusb -vvv''' output) about the device.

== Components ==
* 2 x Micron D9JLR DDR2 SDRAM 512M (32Mx16)
* Xilinx Spartan XC3S400
* Cypress CY7C68013A-56PVXC
* Texas Instruments ADC08D500 High Performance, Low Power, Dual 8-Bit, 500 MSPS A/D Converter
* Analog Devices AD9742 12-Bit, 210 MSPS TxDAC® D/A Converter
* Analog Devices ADCMP562 high speed comparator
* 3 x pca9557
* 4 x omron g6h-2-100

== More photos ==

<gallery>
File:Picoscope 5203 front.jpg|Front
File:Picoscope 5203 back.jpg|Back
File:Picoscope 5203 pcb front.jpg|PCB front
File:Picoscope 5203 pcb back.jpg|PCB back
</gallery>

== Protocol ==

=== Firmware ===

=== Start acquisition ===

=== Sample format ===

=== End acquisition ===

=== Triggers ===

=== Voltage ranges ===

[[Category:Device]]
[[Category:Oscilloscope]]
[[Category:Planned]]